Jackson Safety Pipe Marker Centering Tool, Curv-O-Mark Standard 6, 14775 - Use to measure Pipes 0.5\ and Up, Standard 4\ Y-Type Head, Adjustable Dial Set Level
PIPE MEASURER – This easy-to-use marking tool is designed for pipe fitters and welders as an economical measuring tool for setting center lines, establishing angles and marks for butt-ins, locating points inside pipes and tanks, laying out keyways, and measuring declivity.
STANDARD SIZE – This Curv-O Standard #6 model level tool may be used on pipes and tanks that measure one-half of inch in diameter or larger.
Y-HEAD – The center finder has a 4 inch Y-type head fitted with an adjustable dial bubble protractor (DSL).
BEST OPERATION – Use this manual Jackson Safety hardened centering pin angle finder with a small hammer or mallet to tap the pin in for the most effective pipe marking.
SAFETY STANDARDS – When it comes to providing innovative safety solutions, welding tools with unparalleled features, long-lasting value, and comfort on the job, Jackson Safety has set the standard for the best protective gear and tools in the industry.
6 ft. water pipe heating cable, 42 watt, black color.
Stops metal and rigid plastic pipes from freezing down to -40°F — built-in thermostat automatically turns heating on when pipe temperature is below 42.8° F (close to freezing) and turns heating off once pipe is warmed to 55.4° F (well above freezing).
A single 6 foot heating cable is suitable for 6 foot to 8 foot long pipes that are 3/8 inches to 3/4 inches in diameter, or for 6 foot long pipes that are 1 to 1-1/2" in diameter. NOTE: Use only for water filled plastic (including PEX) or metal pipes. Not for use with anything else, like empty water pipes, fuel lines, hoses, gutters, steam lines, and so on..
Features grounded plug with indicator light.
Pre-assembled, easy to install using the included instructions. Materials required (not included) are: aluminum foil (recommended for plastic pipe), fiberglass plumbing pipe insulation, fiberglass tape or similar with temperature rating 175° F or higher..
Manual Pipe Welder HDPE Butt Fusion Welding Machine Electric Tube Butt Fusion Equipment Hot Melt Solder Welder for 2.48"-7.87" PE PP PB PVDF HDPE PVC Pipes and Fittings
【Application】The welder is suitable for PE PP PB PVDF PPR plastic pipe hot-melt butt welding. High quality design and construction provides an excellent machine for welding both on the worksite and in the factory..
【Welding Size】Welding level (outer dia) is 63mm(2.48”)、75mm(2.95")、90 mm (3.54”)、110 mm (4.33”)、125 mm (4.92”)、140 mm (5.51”)、160 mm (6.30”)、180 mm (7.09”)、200mm(7.87”)..
【Fast Heating Speed】Thick high-quality layer paint, uniform heat conduction, rapid heating of the tube, high work efficiency..
【Stable Performance】The heating plate adopts independent temperature control system and imports large gold paint surface coating, which has good invisibility and stability..
【Adjustable Temperature】Accurate scale temperature adjustment 0-280℃ Manual adjustment and lasting constant temperature..
ATPEAM Butt Welding Clamp | Pack of 16 Small Welding Clamps Auto Body Panel Clamps for Edge to Edge Welding
Premium Material: Panel welding clamps are constructed of zinc-plated steel to ensure maximum durability and strength while resisting rust.
Fits your Project: Each welding square tool pipe clamp can extend the clamp block to provide a .4-inch (1cm) tall gap.
Fits 3/16-inch to 26 gauge sheet metal materials.
Good performance: These small welding clips can be completely fixed before butt welding, leaving only a small gap to make the weld completely penetrate. This is an ideal choice for professionals engaged in sheet metal body repair..
Easy to Use: Loosen the winged nut from the alignment screw then wedge two panels across from each other between the square body and the clamp block.
Tighten the winged nut to ensure a secure hold.
Use all 16 clamps for larger projects, then joint weld between them.
Package Included: Welding accessories set includes 16 welding corner square welder clamps.
Used to make precision butt welds and edge-to-edge welds for patch repairs in floors, wings, door skins, fabricating, and re-skinning projects.
