Prewired Wiring Harness Kit for LP Electric Guitar 2T2V 500K Pots 3-position Toggle Switch with Jack for Dual Humbucker Gibson Les Pual Style Guitar Electronics Replacements White Cap
Circuit wiring set for LP SG EPI Style electric guitar, Material: Metal and wire, Switch Cap: White.
2 volume / 2 tones / 3 way switch, 2 capacitors, 1 input jack socket, prewired components make for an easy install, each tone pot has its own 2A473J capacitor, as well replace all the electronics..
2 Volume and 2 Tone Knob Pots: 2 B500k full size potentiometer, 2 A500k full size potentiometer, Pots Shaft length: approx. 18mm / 0.71", Base diameter: approx. 16mm / 0.63", Switch: Approx. 18 x 28 x 49mm / 0.71 x 1.1 x 1.9 inch.
2 tone potentiometers with the green capacitors and 2 volume potentiometer with no capacitor, pots are smooth and consistent, switch is excellent and cool that it came with a white tip.
Wiring diagram as the picture seventh shown, this harness is completely prewired. All you need to do is solder your pickups to the switch and ground them to the volume pots, more instructions please help to see the description as below. (Any other problem about product or replacement, please help to contact the seller, The way to Contact Seller: Find your order -- Contact Seller, thanks.).
Synchronized or Individual Dual Potentiometer Actuator Controller - 30A - Wired Remote control kit for feedback electric actuator
DUAL-CHANNEL - Connect up to 2x electric actuators with potentiometer feedback to have them travel in parallel, sequence, or individually.
SYNCHRONIZE - Connect devices with potentiometers to synchronize their movements.
SAVE UP TO 3 PRESETS - Use the wired remote to save 3x preset locations.
COMPATIBILITY - With a current rating of 15A, this control system is easy to use with a variety of 12VDC or 24VDC devices. Includes wire harness for each channel.
SPECIAL ATTENTION: Use it only with an actuator with potentiometer feedback. See at our Store PA-14P model..
4000 mm Stroke Draw Wire Linear Displacement Sensor Transducer CWP-M4000 (0-10KOMH)
【Good Quality】The cover shell of KPM12 rod sensor is aluminum, rod is stainles steel, PCB board with machine linear engraving. High precision linearity and repeatability..
【Potentiometer Principle】 This sensor adopts potentiometer principle, output signal is 0-100% of input voltage while changes with displacement..
【Plug & Use】The sensor is with Hessman plug, easy and convenient while using. This sensor can be fixed on machines..
【Wide application】This displacement sensor is widely and common used in injection machine, wood machines, hydraulic machinery..
【Safety】This product is covered with aluminum, rust resistance, long service life. High protection class IP67, good protected, it is workable when powered. Safe to use..
TWTADE 10Pcs Single Linear Rotary Seal Amplifier Potentiometers Type 10k Ohm Knurled Shaft 3Pin RK097N-3-10K
B103 10K Ohm double linear potentiometer, designed for volume adjustment, picture quality and various controls, easy to install and convenient to use, great replacement for your guitar..
Body Size: 75 * 9 * 6mm / 2.95 * 0.35 * 0.24inch(pin not included).
Material: Made of high quality material, sturdy and durable, provides a long life service..
Delicate workmanship with good texture, smooth surface for you to use..
DEVMO DP20V2A Constant Voltage Constant Current Programmable Control Step-Down Supply Power Module
...ble output current range is 0-2.00A, step by 0.01A. Boot voltages can be stored freely and the model has two groups of quick storage voltage. Compared with the traditional analog power supply, it is more convenient to quickly extrac.
Adjusting preset voltage:Pressing SET button, page down to U-SET, press the codding potentiometer, then enter toadjustnumeric value. Press codding potentiometer in turn to choose the numeric value you want to adjust. Turn codding potentiometer to adjust the numeric value. If you want toexit adjusting voltage, press shortly SET. In the process of adjusting preset voltage, if you open output voltage mode by pressing the ON/OFF, the output voltage will be refreshing by increasing or decreasing the.
Power-down storage:If you want to use the present value includingthe preset voltage, the preset current, LCD brightnessat the next time of using the module, you should store those value. In the normal operating(R-MD), Keep pressing SET key until "MEMO" in red appears on LCD display, and then loose the key, indicating the preset voltage has been stored. You can use those value next time..
[Specification]- Type: EC11 Encoder with Screw Thread.
[Rotary encoder]- By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency, unlike rotary potentiometer count, this rotation counts are not limited. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0..
[Applications]- Rotary encoders are widely used in industrial controls, robotics, photographic lenses, computer input devices such as optomechanical mice and trackballs, controlled stress rheometers..
[Package Content]- 5pcs x Rotary Encoder Code Switch Digital Potentiometer.
[Specification]- Type: EC11 Encoder without Screw Thread.
[Rotary encoder]- By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency, unlike rotary potentiometer count, this rotation counts are not limited. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0..
[Applications]- Rotary encoders are widely used in industrial controls, robotics, photographic lenses, computer input devices such as optomechanical mice and trackballs, controlled stress rheometers..
[Package Content]- 2pcs x Rotary Encoder Code Switch Digital Potentiometer.
