Best Printed Circuit Module

ACEIRMC 5pcs 12 Bit WS2812 WS2812B Full Color 5050 RGB Lamp Panel Round LED Ring Lamp Light for Arduino (12 Bit)

  • 4-7V Intelligent reverse connect protection.
  • the power supply reverse connection does not damage the IC The control circuit and the LED share the only power source Control circuit and RGB chip are integrated in a package of 5050 components.
  • form a complete control of pixel point Built-in signal reshaping circuit, after wave reshaping to the next driver, ensure wave-form distortion not accumulate Built-in electric reset circuit and power lost reset circuit Each pixel of the three primary color can achieve 256 brightness display.
  • completed 16777216 color full color display, and scan frequency not less than 400Hz/s Cascading port transmission signal by single line Any two point the distance more than 5m transmission signal without any increase circuit When the refresh rate is 30fps, cascade number are not less than1024 points Send data at speeds of 800Kbps The color of the light were highly consistent, cost-effective.
  • Wattage:0.7W Applications Full-color module, Full color soft lights a lamp strip LED decorative lighting, Indoor/outdoor LED video irregular screen.
Check Stock

20 Pieces 3 Pins AMS1117-3.3 DC 4.75V-12V to 3.3V Voltage Regulator Down Power Supply Buck 800mA Module

  • ...e with: the 3 pins AMS1117-3.3 voltage regulator mini power supply is compatible with Arduino MEGA2560, MSP430 development board, 3.3V low power consumption MCU, FPGA/CPLD PLD programmable logic systems, ARM7 ARM9 ARM11 STM32, etc..
  • Provide more safety: the AMS1117-3.3 800mA DC buck module features overheat shutdown circuit provides overload and over-temperature protection, no worry about safety and bring you more convenience.
  • Operating junction temperature range: -40 to 125°C, welding temperature (25 seconds): 265°C, storage temperature: - 65~150°C.
Check Stock

Professional ZVS Low Voltage Induction Heating Power Supply Module 5V-12V 120W Induction Heating board With Coil(black)

  • One of best heating power supply module..
  • Input voltage DC5V-12V(We are not guarantee the module will work when the voltage is over 12V or less than 5V)..
  • Maximum power 120W(when 12V eddy-current heating)..
  • Ensure all the components welding right, power line connect in right way,than to set up an electric circuit..
Check Stock

Electric Skateboard ESC Kit, 10S 36V Single Drive ESC Substitute Control Mainboard with Remote for DIY Electric Skateboard Longboard

  • Made of high quality chip and electronic components, single drive design can offer excellent and stable performance..
  • The solid structure of mainboard can greatly lengthen the service life. With remote receiver module, so it supports remote control..
  • The well-organized circuit board is easy to install, but needs professional skills..
  • This electric longboard skateboard control system has EMP control module with remote module, it can do as ESC do..
  • With over-voltage, under-voltage, overheating, over-current​ protection, safe and reliable to use, supports speed control, easy to use. With a LED indicator that displays signal status, speed modes, battery percentage..
Check Stock

Songhe HM-10 Bluetooth 4.0 BLE iBeacon UART Module with 6PIN Base Board for Arduino (2PCS)

  • 1. Internal logic level conversion circuit. No need to externally convert 5V level to 3.3V level.
  • 2. The power input port is equipped with anti-reverse circuit. Avoid accidental power plugging, which may cause the module to burn out..
Check Stock

AEDIKO 4pcs Relay Module DC 5V Relay Switch 1 Channel Relay Board with Optocoupler Isolation Support High or Low Level Trigger

  • Fault-Tolerant Design: Fault Tolerant Design, Even if the Control Line is Broken, the Relay will not Operate.
  • All Interfaces of Relay can be Wired Out Through the Terminals Directly,Normally Open and Normally Closed.
  • Optocoupler Isolation:1 Channel Relay Board use Optocoupler Isolation that has Strong Driving Ability and Stable Performance ,The Isolation Circuit Prevent Damages to I / O Port by Relay Switch Current.
  • Jumper Design: The Relay Module has a Jumper That You Can Set Rather the Unit State Changes with High or Low Signal. Has Screw Terminals for Relay (NC,C,NO) and for Input.
  • Wide Application: DC 5V Relay Module Works Well with ARM /PIC /AVR /MCU/Raspberry/CNC Machine/ PS4 etc..
Check Stock

PUSOKEI M.2 SSD Riser Card, M.2 A E Key to M.2 M Key Card, Durable NVME Bluetooth WiFi Card, SSD Adapter Card for Network Card, M.2 SSD, Easy Installation

  • Durable Material: This M.2 A+E Key to M.2 M Key card adopts premium material, which ensures long service life..
  • Conversion Type: This SSD riser card can convert M.2 A+E Key to M.2 M Key interface, great convenience..
  • Widely Compatible: This M.2 SSD riser can is applicable to wireless card type BT type wireless module, also can be used for M. 2 SSD..
  • Easy Installation: 1 x tray, 1 x converter cable and 2 x screws are included in the package, easy to install and use..
  • Stable Performance: This M.2 A+E Key to M.2 M Key card adopts premium printed circuit board, which ensures stable performance..
Check Stock

Liftmaster/Chamberlain/Sentex 41as050-1 Receiver Logic Board Assembly

  • There are 8 lighting modes for you to choose: 1: 2-8 function cycle,2: Star flash,3: Double flash,4: One way fades in and out,5: 4 single flashes, 4 double flashes,6: All fade in and out,7: 4 single flashes,8: All on..
  • It can be connected to a 1.2V nickel-metal hydride battery and a 2V solar panel. The maximum charge current is 400mA and the discharge current is 100mA..
  • Solar light string controller circuit board with power switch and lighting mode switch, easy to operate..
  • The controller module can be used for 100LED solar string lights, solar copper wire lights, solar studs and other lamps..
  • The solar light string controller module is made of glass fiber material, with fine workmanship and durability..
Check Stock

AmScope - Adjustable Circuit Board Holder and Clamping Kit PCB Holder Frame - Single Pack - 1 Piece

  • Adjustable printed circuit board holder (PCB) holds objects in place for soldering, repair or inspection functions.
  • Wide base with rubber feet creates a solid and safe work platform.
  • Spring-loaded clamp holds objects up to 7 ¾” wide (198 mm) securely in place.
Check Stock

Pomelotree LED Window Lights LED Module Lights Waterproof Storefront Lights Business Decorative Lights 12V 5050 LED Lights for Advertising LED Signs Business Store Light 100FT RGB (10 Packs)

  • ...enient for you to install. There are sm-4p connectors on the end of each strand of LED module light. It will be much easier for you to connect the lights. Just plug. No need to crimp male female connectors any more. You should pay special attention to the positive and negative poles of the connectors to avoid short circuit..
  • 【Type】- 5050 SMD module, 12V DC input voltage. With ABS plastic material, Waterproof led window lights can work in -20~60℃. Besides, the color of the plastic will not gradually become yellow after long-term using. You can cut it each led into the length you want, DIY your own LOGO or Lighted Store Signs..
  • 【Energy-saving】- Low power consumption, high energy efficient. The business decorative window lights can make your signs attractive with less cost..
  • 【Widely application】- The Storefront Lights can widely used in store, Restaurant, Coffee, Bar, Bank, Airport, Railway, public advertise and notice .Channel Letters Back lighting, Advertisement Signs, and Signage letters..
Check Stock