Prevent Freezing of Water Line – This winterize blowout adapter kit helps to winterize garden hose, sprinkler systems, faucets, by blowing out water from the water lines/plumbing. It is an environmental friendly winterization way, which greatly reduce the chance of using antifreeze.
Trusted Quality – The fittings made of lead-free brass which contain less than 0.25% lead, care for your health and safety. It is not easy to break or deform, ensure long-lasting service time.
Wide Range of Uses – A quick and easy way to blow out the water lines of your RV, motorhome, camper, boat, and travel trailer, sprinkler systems, outdoor plumbing, garden hoses and more.
Easy Operation – Comes with a 3/4 Inch Female Garden Hose Threading for you to connect the gardening pipe. Besides, two black washers included to prevent leakage between the water tube and water tap.
Standard Threaded Connection – With a 1/4 inch male air compressor quick plug to a male 3/4 inch garden hose inner thread, easy attach air line to water lines or hose system. You can rotate around the Air Flow Regulation Ball Vale to open or close and adjust the air flow rate.
Lisle 22920 8 mm Low Profile Jiffy-Tite Disconnect Tool
Disconnects quick connect push-in connectors found on heavy-duty truck air systems and more.
Smallest size also works on automatic adjusting air suspension systems for automobiles.
Disconnects air systems on brakes, suspension, steering, engine, transmission and other auxiliary equipment.
Also disconnects other quick connect push-in fittings, including: flow control valves, check valves, shuttle valves, quick exhaust valves and other function control fittings in compressed air systems.
Each tool is double-ended to disconnect air lines even in hard-to-reach areas, angled end allows maximum leverage, smaller end fits in tight spots.
2' x 50ft PVC Lay Flat Discharge Hose With Aluminum Camlock C & E Fittings, Cam Lock Fitting Type A included, Heavy Duty Reinforced Pump Backwash Hose Assembly
...IZE]: Backwash pump hose, standard 2 inch diameter, Flat width 3.4 inch.
2 in Aluminum cam lock fittings type C, type E and extra TYPE A adapter. Length: 50 feet.
Temperature Range: 23°F to 149°F (-5°C to 65°C).
[TYPE A FITTINGS]: The item include a type A (male adapter x female NPT threaded ) cam and groove hose fitting, you can directly screw onto pump male threaded outlet, then realize quick connect or disconnect between discharge hose assembly with pump..
[NO LEAK]: Pool Backwash hose doesn’t leak or burst within 90 psi working pressure. Because the delivery hose body adopts fine double-sided coating and fiber reinforcement. The camlock coupling shank is special multi-section structure and added black rubber ring and sealant at the connection..
[WIDELY USED]: Ideal for draining swimming pools, backwash pool filter, sewage pump, sump pump, trash pump, pool drain and sand filter pumps etc.
widely used in household, mine, factory, agriculture, and architectural engineering.
This drain hose can adapt to most outdoor conditions and all seasons..
[EASILY USE]: It can be easily connected, after Type A is connected to the pump, just slide type A male adapter into type C female coupler, press the brass cam levers down with n....
2' x 50ft PVC Lay Flat Discharge Hose With Aluminum Camlock C & E Fittings, Cam Lock Fitting Type F included, Heavy Duty Reinforced Pump Backwash Hose Assembly
...[SIZE]: Backwash pump hose, standard 2 inch diameter, Flat width 3.4 inch.
2 in Aluminum cam lock fittings type C, type E and extra TYPE F adapter. Length: 50 feet.
Temperature Range: 23°F to 149°F (-5°C to 65°C).
[TYPE F FITTINGS]: The item include a type F (male adapter x male NPT threaded ) cam and groove hose fitting, you can directly screw onto pump female threaded outlet, then realize quick connect or disconnect between discharge hose assembly with pump..
[NO LEAK]: Pool Backwash hose doesn’t leak or burst within 90 psi working pressure. Because the delivery hose body adopts fine double-sided coating and fiber reinforcement. The camlock coupling shank is special multi-section structure and added black rubber ring and sealant at the connection..
[WIDELY USED]: Ideal for draining swimming pools, backwash pool filter, sewage pump, sump pump, trash pump, pool drain and sand filter pumps etc.
widely used in household, mine, factory, agriculture, and architectural engineering.
This drain hose can adapt to most outdoor conditions and all seasons..
[EASILY USE]: It can be easily connected, after Type F is connected to the pump, just slide type F male adapter into type C female coupler, press the brass cam levers down with....
Dixon STMP3B Brass Hydraulic Quick-Connect Fitting, Plug, 3/8\ Male Coupler x 3/8\-18 NPT
Straight through quick connect hydraulic coupler for connecting directly to a hose with a male NPT end to connect with a female NPT threaded connection.
Straight through quick connect male plug with a male NPT threaded end.
Valveless construction provides maximum flow with minimum pressure drop.
Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
Used for hydraulic applications in industrial operations.
Dixon STMC6 Brass Hydraulic Quick-Connect Fitting, 3/4\ Male Coupling x 3/4\-14 Straight
Straight through quick connect male coupler for connecting directly to a hose with a male straight thread end to connect with a female straight threaded connection.
Straight through quick connect male coupler with a male straight threaded end.
Valveless construction provides maximum flow with minimum pressure drop.
Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability with NBR seal for high tensile strength and resistance to abrasion, tear, and compression set.
Used for hydraulic applications in industrial operations.
Straight through quick connect hydraulic male coupler for connecting directly to a hose with a female straight thread end to connect with a male straight threaded connection.
Straight through quick connect male coupler with a female straight threaded end.
Valveless construction provides maximum flow with minimum pressure drop.
Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
Used for hydraulic applications in industrial operations.
