Best Quick Coupling E Type

uxcell 8mm to 8mm Bore Rigid Coupling Set Screw L25XD14 Aluminum Alloy,Shaft Coupler Connector,Motor Accessories,Blue w Wrench

  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

High Frequency Transducer, Bandwidth Mixing Board Mixer Module -10dBm for Quadrature Modulation for Base Station for HF VHF Receiver

  • 【Important Data】: SSB noise figure (NF) of 9.75 dB--Input IP3: 28.5 dBm--Input P1dB: 13.3 dBm--Typical LO drive: 0 dBm--Power conversion gain of 1.8 dB.
  • 【Wild Used】: This 5V double balance up and down frequency mixer module is widely used for cellular base station receivers, Radio link down converters, Broadband block conversion, Instrumentation.
  • 【Low Power】: Our 130mA 50 Ohms Balun coil coupling frequency conversion mixer features adjustable bias for low power operation, so you can trust and use this RF mixer inverter with confidence.
  • 【Wonderful Components】: This 5V ADL5801 double balance up and down frequency mixer module is equipped with exposed paddle, 4mm x 4mm, 24-lead LFCSP package, so it will be an ideal choice for you.
  • 【Size】: Power supply: DC+5V@80mA(anti-reverse connection protection.)--RF_IN/RF_LO input frequency range: 10-6000Mhz--Input and output impedance: 50 ohm--Type:Input Balun coupling, Input/output Balun coupling(Optional)--Weight: Approx.15g/0.5oz.
Check Stock

uxcell 1/4 Inch to 1/4 Inch Bore Rigid Coupling Set Screw L25XD14 Aluminum Alloy,Shaft Coupler Connector,Motor Accessories,Dark Blue,2pcs

  • Connection Bore Diameter: 1/4 inch to 1/4 inch.
  • Total Length: 25mm /0.98 inch, Outside Diameter : 14mm/ 0.55 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

uxcell 1/4 Inch to 1/4 Inch Bore Rigid Coupling Set Screw L25XD14 Aluminum Alloy,Shaft Coupler Connector,Motor Accessories,Dark Blue,4pcs

  • Connection Bore Diameter: 1/4 inch to 1/4 inch.
  • Total Length: 25mm /0.98 inch, Outside Diameter : 14mm/ 0.55 inch.
  • Widely used in blowers,3D printer,DIY robots,CNC machine,stepper motors,etc. Similar to rigid clamp couplings, shaft couplers are used to hold bearings and sprockets tightly on the shaft, and are used in motor and gearbox assemblies..
  • Top tight type rigid coupling with 2/4 screws to hold the shaft tightly.
  • high torque with rigidity, low inertia and excellent sensitivity..
  • NOTE: The rigid type basically does not allow eccentricity, and it must be fully adjusted during use..
  • Single piece set screw clamp design makes it easy to set up the items on the shaft and control the holding capacity of the coupling..
Check Stock

Martin 9HS Quadraflex Sleeve, Hytrel, Inch, 6\ OD, 3\ Length

  • For use with specific Martin flange types (J type flanges in the case of JEM and JEMS type sleeves, and all flange types in the case of EM type sleeves) in the Quadra-Flex series flexible coupling assemblies (sold separately).
  • Thermoplastic rubber for resistance to oil and higher temperatures.
  • Three types: one-piece solid (Type JEM), one-piece split (Type JEMS), and two-piece split with a metal retaining ring (Type EM) for applications where the coupled shafts are difficult to separate.
  • Operating temperatures range from -50 to 275 degrees F (-46 to 135 degrees C).
Check Stock

9 Pcs Ortho Drill Bit Set, AO 1mm,1.5mm,2mm,2.5mm,2.7mm,3mm,3.2mm,3.5mm, 4.5mm

  • Included: (1) 1 mm x 10 cm Drill Bit, AO Coupling (1) 1.5 mm x 14 cm Drill Bit, AO Coupling (1) 2 mm x 10 cm Drill Bit, AO Coupling (1) 2.5 mm x 14 cm Drill Bit, AO Coupling (1) 2.7 mm x 14 cm Drill Bit, AO Coupling (1) 3 mm x 10 cm Drill Bit, AO Coupling (1) 3.2 mm x 10 cm Drill Bit, AO Coupling (1) 3.5 mm x 14 cm Drill Bit, AO Coupling (1) 4.5 mm x 14 cm Drill Bit, AO Coupling.
  • Features: Autoclaveable, German Stainless Steel, 5 Year Warranty, O.R Grade.
Check Stock

Martin 9JEM Quadraflex Sleeve, Thermoplastic Rubber, Inch, 6\ OD, 3\ Length

  • For use with specific Martin flange types (J type flanges in the case of JEM and JEMS type sleeves, and all flange types in the case of EM type sleeves) in the Quadra-Flex series flexible coupling assemblies (sold separately).
  • Thermoplastic rubber for resistance to oil and higher temperatures.
  • Three types: one-piece solid (Type JEM), one-piece split (Type JEMS), and two-piece split with a metal retaining ring (Type EM) for applications where the coupled shafts are difficult to separate.
  • Operating temperatures range from -50 to 275 degrees F (-46 to 135 degrees C).
Check Stock

Agatige 2Pcs Clamping Nuts Knob, Female Thread 7 Star Shaped Head Nuts Knurled Clamping Handle Nuts Fastener Black M16 x 80

  • Wide range of nut methods, strong wear resistance, high hardness level.
  • Wide range of applications: coupling steel nuts are widely used in household and office equipment, communication equipment and other machinery industries..
  • Perfect for carrying around: the coupling nut is very suitable for use in wood and humid environments. Hexagon bolts and nuts are very good quality products on the market and are durable..
Check Stock

Bushing Fix UP1KIT - Transmission Shift Cable Bushing Repair Kit

  • Kit includes replacement bushing and application specific installation tools..
  • Text and video instructions along with tech support make installation very easy..
  • Used by many transmission and service professionalsDescriptionThe transmission shift cable linkage kit allows you to quickly and easily repair your shift selector cable by replacing the bushing or grommet. The patent pending coupling and custom molded replacement bushing ensure a quality repair with ease. A professional can perform this repair in under 10 minutes, average time for a non-professional is less than 25minutes. This bushing is made from a material that was designed to outlast the factory bushing and includes everything needed to install. The kit includes DIY instructions, custom molded bushing, and patent pending installation tools. Works in 4T40-E, 4T45-E, and 4T65-E transmissions. This kit fits the following vehicles: Chevrolet Uplander.
Check Stock

Martin 8JEM Quadraflex Sleeve, Thermoplastic Rubber, Inch, 5.063\ OD, 2.5\ Length

  • For use with specific Martin flange types (J type flanges in the case of JEM and JEMS type sleeves, and all flange types in the case of EM type sleeves) in the Quadra-Flex series flexible coupling assemblies (sold separately).
  • Thermoplastic rubber for resistance to oil and higher temperatures.
  • Three types: one-piece solid (Type JEM), one-piece split (Type JEMS), and two-piece split with a metal retaining ring (Type EM) for applications where the coupled shafts are difficult to separate.
  • Operating temperatures range from -50 to 275 degrees F (-46 to 135 degrees C).
Check Stock