SunFounder Raspberry Pi UPS Power Supply Module V2.0 Supports Pass Through Charging, 5V/3A Lithium Battery Power Pack Expansion Board Compatible with Raspberry Pi 4, 3 and All Model B/B+
➢Raspberry Pi UPS - A Power Supply Module designed for Raspberry Pi UPS compatible with Raspberry Pi 4, 3 and all Model B/B+ series. Also suitable for other boards powered by USB (5V/3A) such as Banana Pi/ODROID-C4..
➢Pass Through Charging - Requires two 18650 Batteries (not included), with Pass through Charging function, it can power to the Raspberry Pi while charging ..
➢Over Charge/Discharge Protection - Charging ends when the total battery voltage reaches 8.4V. When the single battery voltage is below 3.2V, the battery protection activates and the battery is no longer discharged..
➢Balance Charging & Over Heating Protection - The battery charging current will be reduced or even discharged if the voltage of a single battery exceeds 4.2V. If the temperature reaches 75 degrees Celsius, the DC-DC will shut down to prevent overheating damage..
➢UPS Output: 5V/3A, UPS Input: 5V/2A, Dimension: 90mm x 56mm x 24mm.
ciciglow Digital Audio Card I2S Interface PiFi DIGI DAC + HiFi DIGI Digital Audio Card Insulated Power Supply Compatible with Raspberry Pi B+ Raspberry Pi 2 Model B,Raspberry Pi 3B 64-bit
★★★【High Performance】 Pifi DAC + PCM5122 DAC, I2S interface, analogue output signal, Compatible with for Raspberry Pi B + a + 2B Raspberry....
★★★【Compatible with】Perfect compatibility raspberry pie official PI HAT size, gold plating process of tall based on circuit board, arc wire....
★★★【Features】Gold-plated RCV Double Clamp and gold-plated 3.5 mm jack socket (Recommended via Amplifier).Provided with an infrared receiver....
★★★【Insulated Power Supply Design】The insulated power supply design, make the raspberry pie nutrition and DAC part of the independent power....
★★★【 DAC 】Increase for double color LED provides state display, red for DAC power indicator (power normal bright), the green light for the....
HiFi DAC+Sound Card Pifi DAC + PCM5122 DAC I2S Interface Analogue Output Signal Digital Audio Card Compatible with Raspberry Pi B + a + 2B Raspberry Pi 3B (64-bit)
...nd. Since the load support is as low as 1K, PCM510xA can drive a variety of parallel products..
Ensure the continuity of signal impedance: Sound card Pifi DAC’s gold-plated RCV double clip and gold-plated 3.5 mm jack socket (recommended by amplifier). It is perfectly compatible with the official PI HAT size of the Raspberry Pi, based on the high gold plating process of the circuit board, and the arc line (high-end HIFI DAC adopts the arc line), which better guarantees the continuity of signal impedance and reduces signal reflection and refraction..
Pifi DAC + PCM5122 DAC: Pifi DAC + PCM5122 DAC, I2S interface, analog output signal, compatible with Raspberry Pi B + a + 2B Raspberry Pi 3B (64 bit). Provide infrared receiving interface..
Get rid of the current sound: The RPI+DAC HiFi kit uses an insulated power supply design to isolate the Raspberry Pi nutrition from the DAC part of the independent power supply, and the beads do not interfere with each other, and get rid of the sound of electric current. With this RPI+DAC HiFi kit, you can easily get more beautiful sounds..
Provide status display: Stereo audio DAC PCM5122 adds a two-color LED to provide status display, red is DAC power indicator (power is normally on), green is DAC light status (decoding ....
Yahboom 4 Port USB 3.0 Hub for Raspberry Pi Jetson Nano ROS Robot, Compatible with USB 3.0/2.0/1.1 Driver-Free Plug&Play, Onboard External USB-A，5V (Micro-USB)，9~24V Power Port, for High-Power Device
...wer supply, this product also supports 5V (micro-USB), 9~24V (DC interface/XH2.54 socket) wide-voltage external power supply. Even if multiple high-power peripherals are connected at the same time, the stability of power supply and signal transmission can be guaranteed..
Support equipment -- Support ROS robot / car, Raspberry Pi / Jetson series board, PC, other boards, industrial computer, etc. Compatible with win7 / 8 / 10, Linux, Ubuntu, MacOS systems, no need drive file, plug and play. If the USB device needs to be restarted, the device can be powered off and restarted through the switching power supply without plugging and damaging the interface..
Size support Raspberry Pi stack installation -- Support installation of Raspberry Pi 4B/3B+/3B,The kit contains the exclusive copper column screw accessories for jetson nano and raspberry pi, the material is of reliable quality, and there is technical help.
MakerFocus Raspberry Pi 4 Power Expansion Board DockerPi Power Board 20W(5V 4A) Power Supply Safe Shutdown with Cooling Fan Infrared Remote Control Compatible with Raspberry Pi 4 and 3B+
DockerPi power board is used to power the Raspberry Pi (or similar SBC) with a typical power of up to 20W (5V/4A) and can run up to 25W (5V/5A) with good heat dissipation..
★It also supplies power to other DockerPi modules to protect the safety of the power supply. It also provides a safe shutdown function, supports infrared remote control switches, button control switches. The link for the one-step automatic installation is obtained in the product description. Restart the Raspberry Pi and complete the installation.
★It has 3*3cm quiet cooling fan, can effectively cool down. We recommend that install the power board on the bottom of the other DockerPi..
★It is recommended to connect 12V 2A or above power input and 12V power from 4-pin headers to other DockerPi, If other modules require 12V power. Note: DockerPi Power Board does not support hot plug..
★Official compatibility test. Support Raspberry Pi, Banana Pi M3, Orange Pi Zero. Other development boards can be compatible if they have I2C peripherals. Note: maybe need to change some software..
[5V 3A UL Listed] iUniker Raspberry Pi 3 Power Supply, Raspberry Pi Power Supply with Switch 15W 5V 3A Micro USB Raspberry Pi 3 b+ Power Switch (UL Listed)
Compatible only with the Raspberry Pi 2, Pi 3 and Pi 3 B+. NOT Compatible with Raspberry Pi 4.
Output: 5V DC / 3.0 A Regulated Input: 100 – 240VAC.
ZOZO 10W 5V 2A 2000mA Multi Tips Switching AC Power Adapter Replacement Power Supply Cord Charger for Tablets Webcam Routers Toys Recorder TV Box USB Hub Bluetooth Speaker and More DC 5V Devices
...tronics. Like Scanner, Router, Bluetooth speaker, Foscam Wireless IP Camera, CCTV camera, USB hub, bluetooth GPS Receiver, tv box, tablets, Baby Monitor, Graco Swing, Home Phone System, VoIP Telephone Routers, Serato DJ Controller, DVR, ADSL Cat, External battery, hubs, switches, Led Strip, String Lights, vibrator, Raspberry pi 3 Raspberry Pi A/A+/B/B+ Raspberry Pi Zero and more 5V devices. (5V ONLY).
Output: 5V 1000mA, 1.5A, 1.75A, 5V 1A, 5V 500mA, 5V 2.1A, Max 10W. DC Tip Polarity: Central Positive(+). Please read manual carefully before using 5vdc power supply..
MULTIPLE TIPS – Selected various popular connectors, this AC adapter can power most of your 5V DC charging devices. Providing you more power choices. DC Tip Dimensions: 3.0×1.0mm, 2.5×0.7mm, 3.5×1.35mm, 5.5×2.5mm, 5.5×2.1mm, 4.0×1.7mm, Micro USB.
Design-safeguard features against incorrect voltage, short circuit, internal overheating and overloading. This 5v Ac power supply charger is made from quality material to ensure the long lifetime. Power your 5v electronics perfectly and replaces lots of 5 volt power chargers.
Package include: 1 x High Quality 5V 2A AC DC Power Adapter, 1 Set x Tips.
Waveshare Overall Evaluation Board Designed for Raspberry Pi Pico Misc Onboard Components for Easily Evaluating The RP2040
Standard Raspberry Pi Pico header, supports Raspberry Pi Pico series boards. 3.5inch resistive touch screen, 65K colorful, bringing clear and vivid display effect.
Standard 3.5mm audio jack, for headphone or other audio peripherals. Micro SD card slot through the SDIO interface, faster access speed than SPI interface.
Integrates battery header and recharge circuit, allows it keep running without wired power supply.
Other rich resources like buzzer, photoresistor, and RGB LED....
Comes with development resources and manual (Raspberry Pi Pico C/C++ and MicroPython examples).
AURSINC SHARI PiHat - Portable SA818 Ham Allstar Radio Interface Compatible with Raspberry Pi 2/3/4 | Raspberry Pi Hosted Allstar Node | UHF Frequency Range 1W 420-450MHz/70cm | Amateur Radio Operator
[What Is It] Small, portable with self contained radio and antenna, SHARI(SA818 Ham Allstar Radio Interface) is designed for construction and uses in the amateur radio service, works with a Pi2/Pi3 or Pi4, SHARI RF output power is 500 to 1000(default) milliwatts.
[Allstar Node] SHARI PiHatU implements a Raspberry Pi hosted Allstar node using a NiceRF SA818 embedded UHF (420-450 MHz|70cm) radio module.
In order to create an Allstar node, SHARI plugs into two USB jacks on a Raspberry Pi2/Pi3 or Pi4 for power, the Allstar interface and radio programming (a short M/F USB extender cable can be used if desired) ；Note: only work with allstar node or any analog node.
[Power Supply] SA818 Ham Allstar Radio Interface is a power supply intended for the version of the Raspberry Pi. These supplies typically provide 5.1 to 5.2 VDC to the Pi. Current requirements vary with version. Numerous problems with Allstar Nodes have been traced to inadequate power supplies..
[Feature 1] Front panel LEDs indicate the status of SHARI-POWER (green), USB Audio CONNECTION STATUS (blinking green), COS (green) and PTT (red).
SHARI PiHat uses 5 volts from the Pi, and the best place to measure it is from pin 8 (+5) to pin 9 (GND) of the SA818 module.
