Wiring Harness 1 Lead, YCHOW-TECH Wiring Harness for LED Light Bar 12V 40A On/Off Rocker Switch Blade Fuse Power Relay Heavy Duty Light Bar Wiring Harness Kit for Truck UTV AVT Boat
Power Relay Fuse: 30A Fuse. Our luxurious Nylon Wiring Harness Kit loads capacity is up to 400W auxiliary lights or other devices, perfect compatible with all devices that use a 12V power source..
HIGH DURABILITY - The flexible strand copper wire and nylon shell provide outstanding electrical conductivity, high temperature resistance and melting resistance..
SAFETY PROTECTION - Power relay for safety and conversion circuit, blade fuse for overload and short-circuit protection. Double protection for you to drive away from danger..
8.2 FT Length Wiring Harness - Approx. 8.2 ft of cable from relay to the lead, the wire is long enough to reach all the part you need..
Package Include - (1) 8.2 ft Nylon jacket wiring harness.
Dixell XR03CX-5N0C1 230V/50-60Hz Digital Thermostat Controller Auxiliary Relay Programmable-Commercial for Refrigerating Units
...n be easily programmed through the keyboard or the by HOTKEY..
Suitable for appliances including:suitable for applications on normal temperature refrigerating units.230V/50-60Hz.
Defrost is performed through a simple stop of the compressor.Parameter id controls the interval between defrost cycles, while its length is controlled by parameter Md..
SAFETY PRECAUTIONS Check the supply voltage is correct before connecting the instrument. Do not expose to water or moisture: use the controller only within the operating limits avoiding sudden temperature changes with high atmospheric humidity to prevent formation of condensation. Warning: disconnect all electrical connections before any kind of maintenance. Fit the probe where it is not accessible by the End User. The instrument must not be opened..
In case of failure or faulty operation send the instrument back to the distributor or to Dixell S.r.l.(see address) with a detailed description of the fault. Consider the maximum current which can be applied to each relay (see Technical Data). Ensure that the wires for probes, loads and the power supply are separated and far enough from each other, without crossing or intertwining..
Aoicrie 5Pcs DC 5V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger
This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
Wide Application These 5V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine /etc..
Aoicrie 5Pcs DC 12V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger
This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
Wide Application These 12V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine etc..
Parts Express 12 VDC 4-Pin Relay Socket With Diode for Starter Kill Circuit
Never go beyond its capabilities. Try to stay 10 to 15% below what the rate is for.
12-volt 5-prong relay. Excellent water-repellent and dustproof ability, but not using it in water.
Be careful when plugging the relay into the socket. If you push hard, you will bend the female connector.
Primary leads use 12 a.w.g tinned copper wire. Coil leads use 16 a.w.g.
SPDT relay: it has both normally open and normally closed terminals, terminal 87A is powered when the relay is inactive and switches the power to terminal 87 when the relay is activated.
