Best Roll Sheave

Phoenix V-Belt Pulley - 5/8in. Bore, 2 1/2in. Outside Dia. Model Number 125058

  • Classical V-belt sheave fits widely available, classical profile V-belts suitable for use in many existing drive designs.
  • Cast iron for resistance to wear and galling.
Check Stock

Martin 3020 2 Taper Bushing, Sintered Steel, Inch, 2\ Bore, 4.25\ OD, 2\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

Indusco 75700006 Zinc Plated Steel Replacement Sheave with Bronze Bushed, 600 lbs Working Load Limit, 3/16\ Cable Size, 2\ Diameter x 1/2\ Bore

  • Measures 2-inches diameter by 1/2-inches bore.
Check Stock

Indusco 75700016 Zinc Plated Steel Replacement Sheave with Bronze Bushed, 800 lbs Working Load Limit, 1/4\ Cable Size, 3\ Diameter x 1/2\ Bore

  • Measures 3-inches diameter by 1/2-inches bore.
Check Stock

Gates A46 Hi-Power II Belt

  • Suitable for all industrial applications, including v-flat drives.
  • Gates curves provide proper cord support and full contact with the sheave-groove for uniform loading, uniform wear, and increased belt life.
  • Flex-Bonded Cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord....
  • The Flex-Weave Cover is a patented fabric construction for longer cover life, providing extended protection to the belt core from oil, dirt and heat.
  • Meets or exceeds RMA standards for static conductivity and oil and heat resistance.
Check Stock

Mytee Products Snatch Block with Hook WLL 2 Ton 3 Sheave 3/8 Inch Wire Rope Wrecker Roll Back Recovery

  • The snatch block is a pulley system with covered and protected yet removable sides..
  • Snatch blocks or pulleys are used to change the direction of the pull to a different angle relative to a fixed point..
Check Stock

Mytee Products Snatch Block with Hook WLL 8 Ton 6 Sheave 3/4 Inch Wire Rope Wrecker Roll Back Recovery

  • The snatch block is a pulley system with covered and protected yet removable sides..
  • Snatch blocks or pulleys are used to change the direction of the pull to a different angle relative to a fixed point..
Check Stock

Gates A31 Hi-Power II Belt

  • Suitable for all industrial applications, including v-flat drives.
  • Gates curves provide proper cord support and full contact with the sheave-groove for uniform loading, uniform wear, and increased belt life.
  • Flex-Bonded Cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration.
  • The Flex-Weave Cover is a patented fabric construction for longer cover life, providing extended protection to the belt core from oil, dirt and heat.
  • Meets or exceeds RMA standards for static conductivity and oil and heat resistance.
Check Stock

Martin 2517 1 1/2 Taper Bushing, Sintered Steel, Inch, 1.5\ Bore, 3.375\ OD, 1.75\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock

Martin 1008 5/8 Taper Bushing, Sintered Steel, Inch, 0.62\ Bore, 1.386\ OD, 0.875\ Length

  • Taper bushing for mounting a pulley, sheave, or sprocket on a drive shaft.
  • Flush-mounted bushing with a split taper for reduced mounting width and a tight clamp to shafts.
  • Sintered steel for greater strength and resistance to wear than steel.
  • Keyed to the shaft to prevent the shaft from rotating in the bushing.
  • Interchangeable with taper bushings from various manufacturers.
Check Stock