Best Servo To I2c Converter Board

Sony CDP-CE335 5-CD Changer Discontinued by Manufacturer

On-board PAJ7620U2 Chip, can directly recognize 9 basic gestures: Up, Down, Left, Right, Front, Back, Clockwise, Counterclockwise, and Swing..
On-board level shift circuit, compatible with 3.3V / 5V logic level, Support I2C interface communication..
Built-in infrared LED and optical lens, can work in low light and dark environment..
Suitable for smart home, office teaching, robot interaction, gesture toys, somatosensory game equipment,ect..

I2C address: 0x20(default),can be modified by soldering A1 and A2 selection pads..
Each pin configurable for input or output..
Open-drain interrupt output pin for input change interrupt..
New Open-Smart PCF8575 IO Expander Board Module I2C to 16IO for Arduino R3 and other MCU to control simple relay, buzzer, button, led..

Access all the pins (i.e. ATP) of the MicroMod Processor Boards with the SparkFun MicroMod ATP Carrier Board! This board breaks out the MicroMod Processor Board's pins on the M.2 connector to 0.1" spaced female headers and PTH pads on the edge of the board..
Features: M.2 Connector. Operating Voltage Range: ~3.3V to 6.0V (via VIN to AP7361C 3.3V Voltage Regulator). 3.3V (via 3V3).
Ports:1x USB type C, 1x USB type A Host, 2x Qwiic Enabled I2C, 1x CAN, 1x I2S, 2x SPI, 2x UARTs, 2x Dedicated Analog Pins, 2x Dedicated PWM Pins, 2x Dedicated Digital Pins, 12x General Purpose Input Output Pins, 1x SWD 2x5 header. Note: Depending on the design of the Processor Board, not all the pins may be accessible..
Additional Features: 1mAh battery backup for RTC. Buttons: Reset, Boot, LEDs. Power. 3.3V. Phillips #0 M2.5x3mm screw included.
Carrier board only. MicroMod processor board will be needed to use..

Used for RC cars trucks airplanes helicopters rc boat servo connection, receiver connection and flight control board..
This servo Y-cable allows you to control two servos with one radio channel..
Material: 22AWG silicone wire.Wire Length: 7CM/2.75".
3Pin wire cable.Male JR plug to 2 Female JR plug Y Harness cable..
Pack of 6 JR style servo splitter cable,unique design, professional quality JR style connectors..

The ESP32CAM is a tiny module based on ESP32 chip and OV2640. You can even program the ESP32CAM through the ESP-IDF by installing the ESP32 Core.
ESP32-CAM WiFi Bluetooth Module WiFi ESP32 CAM Development Board with Camera Module OV2640 2MP for Arduino, Support Image WiFi Upload and TF Card.
Supports interfaces such as UART/SPI/I2C/PWM/ADC/DAC.
Support OV2640 and OV7670 cameras, built-in flash.
Support image WiFi upload and Support TF card.
Bluetooth: Bluetooth 4.2 BR/EDR and BLE standard.
Ultra-small 802.11b/g/n Wi-Fi + BT/BLE SoC module.

Power Supply: 3-5V (Internal Low Dropout Regulator).
Communication: Standard IIC Communication Protocol.
Built-In 16Bit AD Converter, 16-Bit Data Output.
9-Axis Motion Tracking: 3-Axis Gyroscope, 3-Axis Accelerometer, 3-Axis Magnetometer and a Digital Motion Processor (DMP).
MPU9250 Module Includes Pull-Up Resistors On the SDA, SCL, and NCS Lines.
Pull-Down Resistors On the FSYNC and AD0 Lines.
MPU9250 9-Axis 9 DOF 16 Bit Gyroscope Acceleration Magnetic Sensor Using Immersion Gold PCB, Machine Welding Process to Ensure Quality.

The Pico is a low cost, high performance microcontroller board built around the Raspberry Pi RP2040 chip Dual core ARM Cortex M0+ processor at up to 133MHz with variable core frequency 2x SPI, 2x I2C, 2x UART, 3x 12-bit ADC and 16x controllable PWM channels.
Includes Vilros Picoboat Keychain Carrying Case.

The Pico is a low cost, high performance microcontroller board built around the Raspberry Pi RP2040 chip Dual core ARM Cortex M0+ processor at up to 133MHz with variable core frequency 2x SPI, 2x I2C, 2x UART, 3x 12-bit ADC and 16x controllable PWM channels.
Includes Vilros Picoboat Keychain Carrying Case.

Particularly design this keyestudio sensor expansion board V2 for micro:bit. breaks out all the PIO ports on the micro:bit control board into 3PIN interface (GND, VCC, Signal), easy to connect it with other sensor modules..
Extending some commonly-used serial communication interfaces into pin or female headers with 2.54mm pin pitch, such as I2C and SPI communication pins.Allows communication between micro:bit control board and other communication devices..
Two kinds method to power the micro:bit board, through a black DC jack (DC 7-9V) or a mciro USB port (DC 5V) on the shield..
Connection Diagram, Sample Code, Using Method and Resources are provided in our wiki page. Technical support is available via email or message..
Solder is very clean, everything is aligned nicely, all boards are well packed after function, voltage, current testing, protected in a beautiful box. Up to FCC and CE Standard: made from environmentally friendly components and materials..