Best Shafts Gears

Gate Caster Wheel Spring Loaded 4 Inch Swivel Castor 440lbs Capacity with Universal Mount Plate,Fence Gate Wheel

  • Left hand spiral miter 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Spiral angle of 35 degrees better suits this spiral miter gear for higher speed and larger torque applications than straight miter gears.
  • Low carbon steel (.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for 1:1 gear ratio applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

uxcell 19.5mm External Circlips C-Clip Retaining Shaft Snap Rings 304 Stainless Steel 50pcs

  • This External Retaining Ring is used to secure parts on shafts into a machined groove. It features durable steel construction for long-lasting use. Install with pliers..
  • External circlip use for appliance repairs, bearing, gears, pulleys, and various repair projects..
  • Stainless Steel is Superior to Regular Steel and Provides Excellent Rust Resistance in Water Applications, Suitable for Indoor and Outdoor Use..
Check Stock

300 Piece Internal Retaining Ring Assortment

  • 【External Retaining Ring E-Clip Kit】Wide Size Range (Metric): 1.5mm, 2mm, 3mm, 4mm, 5mm, 6mm, 7mm, 8mm, 9mm, 10mm..
  • 【High Quality Stainless Steel 】Made of durable heat-treated 304 stainless steel, with excellent rust resistance feature. Providing the good resisitance to corrosion and high temperature, holding strongly and lastingly..
  • 【Easy to Use】This E clip kit is easy to assemble and disassemble. Suitable for small size shaft to position parts and prevent them from falling off..
  • 【Storage Box】Come with storage case and each size is neatly put in it's individually compartment in a transparent storage case. Easy to get the size you need and quick access!.
  • 【Widely Used】Good for retension of bearings, gears, pulleys, axles, shafts, and other moving parts. Provides excellent rust resistance in water applications, suitable for Indoor and Outdoor Use..
Check Stock

Door Controller Adjustable Telescopic Arm Hydraulic Buffer Door Closer for Residential and Commercial Use Middle-Weight Door

  • With high strength and rigidity, good toughness, high temperature resistance and high pressure resistance..
  • Hydraulic buffer door closer, the rotating shaft rotates softly, ensuring smooth opening and closing of the door..
  • Using high‑hardness cast aluminum and cold‑rolled steel materials, strong and durable, wear‑resistant..
  • After multi‑layer crystal diamond processing, the chemical performance is stable and corrosion resistant..
  • The gears and shafts at both ends adopt multi‑layer quenching process, and surface hardness is above HRC80..
Check Stock

Martin TS2020 Spur Gear, 20° Pressure Angle, High Carbon Steel, Inch, 20 Pitch, 1/2\ Bore, 1.1\ OD, 0.500\ Face Width, 20 Teeth

  • Transmits torque between parallel shafts to provide rotational power to another part of a motorized system.
  • Pressure angle of 14.5 degrees for a higher contact ratio between gears, resulting in quieter operation than larger pressure angles.
  • Diametral pitch of 16 for applications requiring a balance between transferring torque and controlling changes in speed and direction of rotation with precision.
  • High carbon steel for tensile strength and hardness.
Check Stock

Andantex R3303 Anglgear Right Angle Bevel Gear Drive, Universal Mounting, Two Output Shafts, 3 Flanges, Inch, 5/8\ Shaft Diameter, 1:1 Ratio, 1.21 Hp at 1750rpm

  • Carburized case hardened "Gleason Coniflex" bevel gears, AGMA quality class 9.
  • Compact precision machined aluminum housing coated with a chemical film.
  • Stainless Steel 416 precision ground shafts supported by 2 Ball Bearings.
  • Grease lubricated for life and bearings sealed with Buna-N seals.
Check Stock

Boston Gear HLK103Y Miter Gear, 1:1 Ratio, 20 Degree Pressure Angle, 0.750\ Bore, 10 Pitch, 20 Teeth, Steel

  • Straight miter 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Hardened teeth for 1:1 gear ratio applications where hardness and strength are needed to transmit torque and motion.
  • Bore has keyway and setscrew for use with keyed shaft.
Check Stock

Boston Gear LSA102YR Spiral Miter Gear, 35 Degree Spiral Angle, 1:1 Ratio, 0.625\ Bore, 12 Pitch, 18 Teeth, Steel

  • Right hand spiral miter 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Spiral angle of 35 degrees better suits this spiral miter gear for higher speed and larger torque applications than straight miter gears.
  • Low carbon steel (.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for 1:1 gear ratio applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Martin S1215 Spur Gear, 14.5° Pressure Angle, High Carbon Steel, Inch, 12 Pitch, 5/8\ Bore, 1.417\ OD, 0.750\ Face Width, 15 Teeth

  • Transmits torque between parallel shafts to provide rotational power to another part of a motorized system.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Diametral pitch of 16 for applications requiring a balance between transferring torque and controlling changes in speed and direction of rotation with precision.
  • High carbon steel for tensile strength and hardness.
Check Stock

Boston Gear NA72 Spur Gear, 14.5 Pressure Angle, Cast Iron, Inch, 20 Pitch, 0.375\ Bore, 3.700\ OD, 0.375\ Face Width, 72 Teeth

  • Transmits torque between parallel shafts to provide rotational power to another part of a motorized system.
  • Pressure angle of 14.5 degrees for a higher contact ratio between gears, resulting in quieter operation than larger pressure angles.
  • Diametral pitch of 20 for applications requiring a balance between transferring torque and controlling changes in speed and direction of rotation with precision.
  • Cast iron for compressive strength and resistance to wear.
Check Stock