TOPINTECH Stainless Steel Well Pump 1HP 110V 20GPM 223ft Head Deep Well Submersible Pump for Domestic, Civil and Industrial
...ad-in line is rubber sheathed type with reliable sealing and good aging resistance.
the pump casing made of high-strength thermoplastic PC.
the impeller uses POM plastic. These materials have high strength, strong impact and wear resistance..
【Wide Voltage Motor】Single-phase 230V motor can run at 180-250V, single-phase 110V motor can run at 100-120V. Pure copper core motor, F-class insulation enameled copper wire, pumping power is more adequate, more safe and reliable..
✔【NEMA Standards】In strict accordance with the National Electrical Manufacturers Association NEMA standards. The advanced rotor spline machining process ensures the hardness, finish, precision, consistency and wear resistance of the rotor, reducing rotor wear at high speeds and ensuring smooth motor operation..
【Wide Application Scenarios】Accurate IAE pressure balance design makes the motor dive deeper；TOPINTECH's special mechanical seal for deep-well pumps for longer motor life；High strength anti-sand fluid components can applied to harsh working conditions. They can be used for deep well/ water tower water supply, agricultural irriga....
6 Pack Mini L298N DC Motor Driver, MELIFE MX1508 Mini Dual Channel 1.5A 1.5A 2 Way PWM Speed Controller Dual H-Bridge Replace Stepper
Motor drive module is ideal for use in battery-powered smart car, toy cars, robots..
Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor..
Supply voltage 2V -- 10V, can drive two DC motors or a 4-wire 2-phase stepper motors ,can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed..
Dual 1.5A * 2, the peak current to be 2.5A, built-in thermal protection circuit, do not be afraid motor stall burned, automatic recovery after the temperature dropped..
Use of imported original chip, built-in low on-resistance MOS switch, minimal heat, no heat sink, small size, low power consumption, is ideal for battery powered..
Price For: Each Hz: 60 Motor Shaft Rotation: CCWSE Phase: 1 Motor Sub Application: Pool and Spa Pump Motor Application: Pump Motor Enclosure Design: Open Dripproof Motor Thermal Protection: Auto Standards: UL Recognized (E25022/46412), CSA Certified (LR43341), UL 1081, 1563, 1795 Approvable Voltage Compatibility: 115, 120, 230, 240, 115/230, 120/240 Shaft: Threaded 3/8-16 UNC-2A.
Voltage: 115/230 Shaft Material: Stainless Steel Shaft Length: 1-13/16" Nameplate RPM: 3450 Motor Mounting Type: Rigid Base Item: Pool and Spa Pump Motor Motor Design: Capacitor-Start HP: 1-1/2 Ins. Class: B Shaft Dia.: 1/2" Full Load Amps: 16.0/8.0 Finish: Black Motor Service Factor: 1.00 Motor Bearings: Ball Frame: 48Y Country of Origin (subject to change): Mexico.
AOICRIE 4PCS L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper for Arduino
L298N as Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects, Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient, To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously.Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled..
Easy to Use No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use..
Wide Usage Great for DIY Smart Car Robot Power MEGA R3 for Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits..
AOICRIE 5Pcs L298N Dual H Bridge Stepper Motor Driver Board For Arduino (5pcs)
【Package Included】- 2pcs L298N Motor Driver Controller Board Modules..
【Item Condition】- Drive voltage 5V-35V, high working power to 46V. Large current can reach 3A MAX and continue current is 2A. Power to 25w.(NOTE: To avoid damage, please use an external 5V logic supply when using more than 12V driving voltage.).
【High Quality】- Use L298N as the main driving chip, so the module has such features as strong driving ability, strong anti-interference and low calorific value. And it also use large-capacity filter capacitor and diode with freewheeling protection function, thereby improve the reliability of module..
【High Efficiency】- Dual-channel H-bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..
【Easy of Use】- No assembly required. This L298N board comes ready to go. Just wire up motors and power, this thing will work wonders..
RATTMMOTOR 110V Water Cooled Spindle Motor Kit 2.2KW ER20 Spindle Motor φ80mm 24000RPM+2.2KW VFD 110V Inverter Variable Frequency Drive+80mm Spindle Mount+80W Water Pump for CNC Router Milling Machine
【2.2KW Spindle Motor】: ①This is a 110V-2.2KW water-cooled 15A Φ 80x213mm spindle motor come with a ER20 nut and collet, and equipped with a....
Usongshine Stepper Motor Driver TB6600 4A 9-42V Nema 17 Stepper Motor Driver CNC Controller Single Axes Phase Hybrid Stepper Motor for CNC/42 57 86 Stepper Motor（1 pcs
Package included: 1 x Stepper Motor Driver..
✿Stepper Motor Driver✿: 9V-42V DC power supply, H bridge bipolar constant phase flow drive. The maximum 4.0A of the eight kinds of output current..
✿The largest 32 subdivision of the 6 models are optional.
Suitable for 4Wires, 6 wires and 8 wires stepper motor. it can control 2 phase stepper....
✿Protect form✿: Energy-saving semi-automatic current lock function, built-in temperature protection and over current protection, under voltage....
✿Suitable for a wide range of stepping motors of Nema 17, 23 and 24 can used in various kinds of machines, such as X-Y-Z tables, labeling machines,....
