Wiring Harness 1 Lead, YCHOW-TECH Wiring Harness for LED Light Bar 12V 40A On/Off Rocker Switch Blade Fuse Power Relay Heavy Duty Light Bar Wiring Harness Kit for Truck UTV AVT Boat
Power Relay Fuse: 30A Fuse. Our luxurious Nylon Wiring Harness Kit loads capacity is up to 400W auxiliary lights or other devices, perfect compatible with all devices that use a 12V power source..
HIGH DURABILITY - The flexible strand copper wire and nylon shell provide outstanding electrical conductivity, high temperature resistance and melting resistance..
SAFETY PROTECTION - Power relay for safety and conversion circuit, blade fuse for overload and short-circuit protection. Double protection for you to drive away from danger..
8.2 FT Length Wiring Harness - Approx. 8.2 ft of cable from relay to the lead, the wire is long enough to reach all the part you need..
Package Include - (1) 8.2 ft Nylon jacket wiring harness.
SparkFun Qwiic Single Relay-Up to 5.5A at 240VAC Multiple I2C addresses Available Turn on/Off high Power Device from Low Power microcontroller No Soldering Large Power Loads w/Simple I2C Commands
Have you ever wanted to control something powerful or have you ever needed to turn on/off a high power device from your Arduino compatible board or another low powered microcontroller? No soldering needed to get started. Plug and play. Code available. Small footprint..
The Single Relay board can handle up to 5.5A at 240VAC for long periods of time and allows you to control large power loads with simple I2C commands. Utilizing our handy Qwiic system, and on-board screw terminals, no soldering is required to connect it to the rest of your system!.
The Qwiic Relay comes with a default I2C address of 0x18 but can be changed with a simple command allowing you to control over 100 Qwiic Relays on a single bus (but please be aware that toggling lots of relays on a 3.3V bus can cause voltage spikes so an external power supply will be required)!.
In addition, there is an address jumper on the back of the board. Closing this jumper with solder will change the address to 0x19..
Operating Voltage: 1.7V-3.6V. Coil Resistance: 23.5Ω. I2C Address: 0x18 (Default), (Jumper changes to 0x19). Max Current (Through Relay): 5.5A (240 VAC).
Aoicrie 5Pcs DC 5V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger
This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
Wide Application These 5V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine /etc..
Aoicrie 5Pcs DC 12V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger
This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
Wide Application These 12V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine etc..
Parts Express 12 VDC 4-Pin Relay Socket With Diode for Starter Kill Circuit
Never go beyond its capabilities. Try to stay 10 to 15% below what the rate is for.
12-volt 5-prong relay. Excellent water-repellent and dustproof ability, but not using it in water.
Be careful when plugging the relay into the socket. If you push hard, you will bend the female connector.
Primary leads use 12 a.w.g tinned copper wire. Coil leads use 16 a.w.g.
SPDT relay: it has both normally open and normally closed terminals, terminal 87A is powered when the relay is inactive and switches the power to terminal 87 when the relay is activated.
Painless Performance 80132 Single Pole, Double Throw Relay, 40 Amp
★ The 8-channel relay module is equipped with transistors, diodes and optocouplers to switch higher loads safely, reliably and with little power. The module is also equipped with generously dimensioned relays in order to be able to reliably carry out many switching processes..
★ 5V 8-channel relay module, each relay requires 70mA for switching (switching capacity AC: max. 250V / 10A.
★ 5V 8-channel relay module can be controlled directly with a microcontroller Raspberry Pi, Arduin, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic, etc..
★ The relay acts as a switch that responds to a signal from the Arduin. Because of this, it is widely used in IoT projects to control lights and other electronic devices..
★ Application: MCU control, PLC control, industrial area, smart home.If you need this relay, you can buy it directly. If there is a problem during use, you can contact us at any time to refund or replace it..
EVTSCAN Latest DPA51CM44 3-Phase Monitoring Relay, Current/Voltage Monitoring Relay Phase Sequence Protector for Three-Phase System, Without Neutral, Phase Loss, 208-480VAC
✈ PRODUCT NAME---Voltage Monitoring Relay.
Protection function: over voltage, under voltage.
Contact capacity: 6A 250VAC (resistivity).
✈ REAL-TIME MONITORING---The voltage monitoring relay could achieve real-time monitoring of dc overvoltage and undervoltage faults, and over-voltage, under-voltage value, and action time can be adjusted.
✈ MAIN FEATURES---The voltage monitoring relay is of 2 sets of normally open and normally closed contacts, 2 indicator lights indicate various working conditions, no additional auxiliary power supply is required.
✈ 35MM GUIDE RAIL---With 35mm guide rail and standard modular structure, the voltage monitoring relay is easy to install, easy to operate.
✈ TYPICAL APPLICATIONS---The voltage monitoring relay is typically applied in dc motor, battery,UPS power supply, dc switchgear, dc panel, industrial control system.
