The latest generation,Premium stepper motors,quiet operation and reliability,Perfectly Replace for the older and faulty XC5-168, X15-168 ,X25-168 and....
Used for the repair of the speedometer,tachometer,oil pressure gauge,transmission temperature gauge, battery voltage gauge, water temperature gauge or....
Each gauges of your instrument cluster need one motor,since one stepper motor went out will result all the motors go out soon. check the stepper motor....
It is easy to use,but you’d better to search the instructions Video on Internet first,which is very helpful.
Dr.Roc-Most trusted auto accessories expert,millions buyers' choice, excellent customer service with 12-month warranty.
3-Axis 32-bit ARM Based CNC Controller,GRBL 1.1F USB Port CNC Engraving Machine Control Board with Fan Cooling,Support 500W Spindle/NEMA23 Stepper Motor/Laser (A4988+Fan)
Model:3 Axis GRBL 1.1F USB Port GRBL Control Board.
Compatibility: support 12V/24V laser, TTL/PWM modulation signal, 3P interface and 2P+2P interface.
support 775 motor, 200W/300W/500W spindle.
support dual Y-axis use, three-axis and two-axis switching use.
support X/Y/Z limit switch, Z-axis probe, emergency stop switch.
Support stepper motor: 12V, within 2A maximum current, within 1.5A recommended. (Stepper motor 42, 57).⚠️Please check the wire sequence when connecting the stepper motor, the wire sequence may be different for different motors, wrong connection may burn the motor and the motherboard..
Support software:LaserGRBL/Lightburn/Candle(3 axis)/Universal Gcode Sender.
Tip: Before you connect the motherboard, please carefully check the need to connect the device wire sequence (laser, motor) to prevent a mismatch of wire sequence, burn the device. Customer service 24H online, to provide you with help..
AOICRIE 4PCS L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper for Arduino
L298N as Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects, Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient, To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously.Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled..
Easy to Use No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use..
Wide Usage Great for DIY Smart Car Robot Power MEGA R3 for Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits..
ANNOYTOOLS ARM 32-bit 3-Axis CNC Controller,GRBL 1.1F USB Port CNC Engraving Machine Control Board with Fan Cooling DRV8825 Standalone Driver,Support 500W Spindle/NEMA17/23 Stepper Motor/Laser Module
Model:3 Axis GRBL 1.1F USB Port GRBL Control Board.
Compatibility: support 12V/24V laser, TTL/PWM modulation signal, 3P interface and 2P+2P interface.
support 775 motor, 200W/300W/500W spindle.
support dual Y-axis use, three-axis and two-axis switching use.
support X/Y/Z limit switch, Z-axis probe, emergency stop switch.
Support stepper motor: 12V, within 2A maximum current, within 1.5A recommended. (Stepper motor 42, 57).⚠️Please check the wire sequence when connecting the stepper motor, the wire sequence may be different for different motors, wrong connection may burn the motor and the motherboard..
Support software:LaserGRBL/Lightburn/Candle(3 axis)/Universal Gcode Sender.
Tip: Before you connect the motherboard, please carefully check the need to connect the device wire sequence (laser, motor) to prevent a mismatch of wire sequence, burn the device. Customer service 24H online, to provide you with help..
SCITOO 2Pcs X27.168 Stepper Motor Speedometer Instrument Gauge Cluster Repair Kit Fit for GM For Toyota For Honda For Ford For Chrysler For Chevy Silverados Tahoes Yukons Suburbans
Universal Stepper Motor Repair Kit:Total 2pcs,used for Stepper Motor speedometer,tachometer,oil pressure gauge,transmission temperature gauge, battery....
X27 168 Stepper Motor Kit also fit for 25 168, XC5 168, X15 168,Silverados, Suburbans, Tahoes, Trailblazers, Yukons.
Why do you need them,they can fix the problems of dead gauges, jumpy readings, sticky needle movement, gauges that ratchet up or down, gauges pegged....
Installation:You can search the instructions Video on Internet first,if you no found it,you can ask us for help..
Notice:This item not fit all vehicals,please confirm your year/make/model before buying..
8PCS L298N Motor Drive Controller Board Dual H Bridge DC Robot Stepper Motor Compatible with Ardu-ino Electric Projects, Smart Car Robot
Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..
The L298N driver module, using L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface, you can chip circuitry to 5V power supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential..
Terminal driver part of the supply area VMS: +5V ~ +35V.
Drive part of the peak current Io: 2A / Bridge.
Logical part of the terminal power supply range Vss :4.5-5 .5V.
Logical part of the operating current range: 0 ~ 36mA.
The control signal input voltage range: 4.5-5.5V low 0V high.
To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
High working power to 46v, large current can reach 3A MAX and continue current is 2A, power to 25w..
Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability, large capacity filter capacitance,afterflow protection diode, more stable and reliable..
Upgraded Ender 5 Plus Silent Mainboard V2.2.1/V2.2 with TMC2208 Driver Customized Super Quiet Mute Motherboard for CR-10S/ CR-10 S4/ CR-10 S5/ CR-X/CR-20/ CR-20 PRO 3D Printer
Upgraded silent mainboard for ender 5 plus printer, V2.2 or V2.2.1 Version shipped randomly(they have same function, just the version number is....
Super Quiet and Noise Reduction. Use TMC2208 Stepper Motor Drivers, which the key component to eliminate the printer's motor when printing..
Notice: This new upgraded silent mainboard does not currently come pre-installed on ender 5 plus..
Bootloader pre-installed. The firmware can be modified by Cura with the USB cable..
Concern for safety. Thermal runaway protection is enabled, if the temperature rises out of control, the printer will stop heating and halt....