A-Team Performance - EFI Fabricated Intake Manifold with Fuel Rails and Throttle Body Short - Compatible with GM Chevrolet LS3 L92 SBC Small Block Chevy V8 GEN. III/IV (LS-BASED) Black
EFI Fabricated Intake Manifold with Fuel Rails and Throttle Body Short Black.
Compatible With: Chevrolet Small Block V8 Gen. III/IV (LS-based) · 4.8 L / 293 In3 (L20, Ly2) · 5.3 L / 325 In3 (Lc9, Lh6, Lh8, Lmg, Ly5) · 6.0 L / 364 In3 (L76, L96, LFA, LY6) · 6.2 L / 376 LN3 (L92, L99, LS3, LSA) Rectangle Port Intake only!.
Fabricated Aluminum Sheet Metal Intake Manifold -102MM Throttle Body -Fuel Rails & Cross Over -4-Bolt LSX Gaskets & Hardware are included..
Throttle Body is Dive by Cable Overview We Designed Our Fabricated Aluminum Sheet Metal Intake Manifold to Improve the Look and Performance of Your LS Engine..
Akozon Air Turbonator, Car Air Intake Double Fan Turbine Charger Fuel Saver Turbo Charger(Red)
Professional Design : The fan blades of this air intake turbonator are designed with a professional angle to enhance the gas flow rate. Double-sided 10-blade prfor Opellers allow the turbine to deliver super-large output.
Energy Saving : Exquisite craftsmanship and high performance,use this fuel saver turbonator could save about 5%-15% of fuel for your vehicle..
Aluminum Alloy Material : The pick-up piece is made of high-strength aluminum alloy, which has durability, corrosion proof, non-deformation, light weight but high hardness, allows to withstand slight collision.And will not be deformed due to long-term use..
Installation instructions: The power acceleration system turbo is installed in the intake hose between the original car bellows and the throttle va e. When installing, the thickness of the rubber collar should be configured according to the diameter of the original car's intake hose..
Work Principle : When the engine is normally started, the turbonator could take advantage of natural intake of the engine to drive the fan to rotate at a high speed. While rotating, a large....
XTechnor Tesla Model 3 Air Intake Filters Cabin Air Vent Intake with Activated Carbon Air Conditioning Air Intake Inlet Cover for 2017 2018 2019 Tesla Model 3
Best Part to keep filter life longer- XTechnor Tesla Model 3 Air Intake Filters is Customed fit for 2017 2018 2019 Tesla model 3 exterior accessories frunk air inlet cover..
UPGRADED PROTECTION- Unlike the other intake grille, XTechnor carbon air inlet vent cover can keep leaves or small stuff from clogging up and block impurities, fall into the AC intake system. Even prevents harmful fine particles and dust from entering the vehicle cabin while keeping clean and healthy environment to passengers..
Apply High Quality Air Filter: (1)Fine fiber filter paper and small molecular material, with dust collection and filtration effect.
(2)High-performance activated carbon strongly adsorbs odors and harmful gases in the air.
(3)A melt blown electrostatic layer is added to trap fine particles by electrostatic charge..
ONE STEP TO INSTALL- It is easy to Install, take off the original air conditioning air intake grille cover, and just place the air intake filters to there without any tools..
XTechnor PROMISE – We offer a LIFETIME, NO-QUESTIONS-ASKED, MONEY-BACK GUARANTEE to our tesla model 3 owner after ordering our car air filter..
2 x NEW Improved 6.0 6.0L Ford Powerstroke Diesel LOADED O-RING 18mm Cylinder Head PAIR 2003-07 No Core (18MM O-ring)
High grade aluminum, bronze valve guides, hardened seats, advance port design for greater air flow.
This head is 200cc intake runner with a 68cc combustion chamber, 68cc combustion chambers improve performance and retains stock compression on 1970 and earlier.
Lighter than Iron Heads. Each Head weighs 10.33kg.
Dokili High Rise Single Plane Intake Manifold for Small Block SBC Vortec 350
【Fitment】Dokili aluminum intake manifold for small block engines using the 1996 and later Vortec (Gen 1+) cylinder heads..
【Features】Dokili intake manifold comes with 360° single plane and high rise designs, providing excellent high RPM power, from 3,000 to 7,500 RPM. It features four corner water ports, a tapped fifth port in the front face, nitrous bosses and dual distributor holddowns..
【Premium Material】Built with natural finish aluminum of superb quality and fit. Permanent mold casting. Angles and straightness comparable to factory manifolds. The port size on this manifold is 2.06" x 1.18". Manifold Height is 6.06"..
【Superior Design】Cast-in bosses on intake runners can be drilled and tapped for use with nitrous. Dual distributor hold-down provisions for extra protection against distributor rotation. Ideal port position allows custom porting for maximum power..
【Package Include】1X SBC Intake manifold. Professional installation in highly recommended..
K&N Cold Air Intake Kit: Increase Acceleration & Towing Power, Guaranteed to Increase Horsepower up to 11HP: Compatible with 5.7L, V8, 2019 Dodge Ram 1500, 63-1578
GUARANTEED INCREASE IN HORSEPOWER & TORQUE: K&N cold air intake systems provide a less restrictive path for airflow, increasing the volume of cool, oxygen-rich air into your engine an estimated increase up to 11HP and up to 15.5 ft.lbs. of Torque.
HEAR THE GROWL: K&N’s intake systems allow your engine to breathe and sound as it should- your engine will growl on acceleration and return to quiet once at speed.
DYNO TESTING YOU CAN TRUST: K&N air intake horsepower/torque testing is performed on wheel-based dynamometers and the reports are include with each intake system.
BETTER TOWING: Air intake kit improves acceleration and uphill performance when towing by improving throttle response and overall horsepower and torque.
FEATURING K&N’s SIGNATURE, REUSABLE AIR FILTER: Combines 4 layers of pleated, breathable cotton with K&N’s red filter oil to absorb dirt and dust particles, allowing clean air to continue flowing into your engine, only needs cleaning every 100,000 miles under normal highway driving conditions.
