Best Stainless Steel Exhaust U bolt

3" 2 Bolt Flange Catback Exhaust Muffler Pipe Extension Flange Steel Adapter

  • Material: Made of multi layer stainless steel and graphite, which is durable and directly to replacement easily.
  • Bolt hole center spacing 105mm/4.13".Minimum inner bolt to bolt distance of 90mm/3.55" Maximum outer bolt to bolt distance of 121mm/4.76".
  • Package Included: 2 * high temp exhaust gasket.
Check Stock

2 Pcs Stainless Polished Muffler Exhaust Tip Finisher Compatible with 2016-2020 Honda Civic

  • Fits 2012-2020 Honda Civic With OEM Exhaust System (Will Not Fit Hatchback Sport or Si or Type-R).
  • Package includes: 2 x Exhaust Pipe Tip Finishers as Shown (Quantity 1 means 2 Exhaust Tips).
  • Made Of Stainless Steel Material in Nice Polished Chrome Finish.
  • Easy Installation- Direct Bolt-On To OEM Exhaust With Adjustable Screws.
  • Dramatically Enhance The Rear Appearance of your Car. Gives it a Sport Tone Right Away..
Check Stock

MagnaFlow Cat-Back Performance Exhaust System 16518 - Street Series, Stainless Steel 3in Main Piping, Single Passenger Side Rear Exit, Polished Finish 4in Exhaust Tip - F-150/Mark LT Exhaust Kit

  • BOLT-ON INSTALLATION – MagnaFlow utilizes state-of-the-art 3D scanning technology during the research and development process to ensure that this exhaust system will fit and outperform the original equipment. CNC precision robotic manufacturing and mandrel bent tubing allow for hassle-free bolt-on installation.
  • STAINLESS-STEEL CONSTRUCTION – Highly corrosion resistant, Stainless-Steel construction incorporating CNC precision robotic manufacturing for quality fitment and longevity. Built to be the exhaust that lasts the lifetime of your vehicle.
  • LIMITED LIFETIME CONSTRUCTION WARRANTY – Performance that lasts. Enjoy worry-free ownership knowing that you’re backed by MagnaFlow’s limited lifetime construction warranty.
Check Stock

MagnaFlow Cat-Back Performance Exhaust System Street Series Kit 15712 - Designed for the 2001-2005 Honda Civic - 2.25in Main Piping, Single Straight Passenger Side Rear Exit, Polished 4in Exhaust Tip

  • BOLT-ON INSTALLATION – MagnaFlow utilizes state-of-the-art 3D scanning technology during the research and development process to ensure that this exhaust system will fit and outperform the original equipment. CNC precision robotic manufacturing and mandrel bent tubing allow for hassle-free bolt-on installation.
  • STAINLESS-STEEL CONSTRUCTION – Highly corrosion resistant, Stainless-Steel construction incorporating CNC precision robotic manufacturing for quality fitment and longevity. Built to be the exhaust that lasts the lifetime of your vehicle.
  • LIMITED LIFETIME CONSTRUCTION WARRANTY – Performance that lasts. Enjoy worry-free ownership knowing that you’re backed by MagnaFlow’s limited lifetime construction warranty.
Check Stock

SEUNMUK 4 Pack 2.5 Inches Exhaust Clamp Sleeve, Stainless Steel Butt Joint Band Clamp Exhaust Coupler Exhaust Band Clamp Sleeve for 2.5-Inch OD Exhaust Pipes, Mufflers

  • ROBUST CONSTRUCTION - The stainless steel exhaust clamp is high-quality 304 stainless steel material, well polished with smooth mirror finish and high strength, which is solid and durable to last and can be reused for a long time..
  • EASY TO JOINT - No welding design, the joint exhaust band clamp features a practical components including bolts, nuts and I-block, you can easily mount or disassemble them, and you can also wrap some exhaust heat tape to enhance complete sealing..
  • TIGHT SEALING - Uniform distribution of clamping force will not crush the pipeline, which can provide tight seal and keep off exhaust and noise leakage. The exhaust band clamp sleeve can close fit on the exhaust pipes or mufflers..
  • PRACTICAL AND MULTIPURPOSE - 4 packs of joint exhaust muffler clamps is designed with 2.5-inch diameter and 3 inches length, which fits for exhaust pipes or mufflers, manifolds, catalytic converters of that with an outer diameter of 2.5 inches..
  • SATISFACTORY SHOPPING EXPERIENCE - If you have any dissatisfaction with exhaust clamp 2.5 inch, you will get a full refund within 30 days. If you have any questions about the product, please feel free to contact us, we will provide you with a satisfactory solution..
Check Stock

Exhaust Tip 5.00' Dia OD X 10.00' Long 2.50' inlet Slant Double Wall Stainless Blue Flame Wesdon Exhaust Tip

  • 【Dimension】 ID: 4″ OD: 10″ Length: 18″ Angled Roll Bolt Chrome.
  • 【Design】 Bolt-On installation and Angled Cut – Rolled Edge design. Small hole on the bottom of the exhaust tip facilitate the drainage of accumulated water and prolong the service life of the exhaust tip.
  • 【Material】 Made of High quality Stainless steel has very strong anti-corrosive, Never Rusty..
  • Professional installation is highly recommended.
  • 【Wide Application】 To ensure proper fit make sure your exhaust tailpipe INLET diameter is 4 Inch.
Check Stock

Aopin Round U-Bolts 1-1/2 inch 38mm M6 Inner Width 304 Stainless Steel 8pcs Self-Locking Nylon Insert Hex Nuts Flat Washers for Car/Motorhome/Sailing Trailer Replacement Part and Accessorie 4Pack

  • STOP: ONLY USE a Hand Socket Ratchet or wrench to run the nuts up and tighten..
  • DO NOT USE an impact or powered socket driver. Ignoring this instruction will cause U-Bolt Galling / Seizing / Breaking / Failure / Expletives / Sawzall. Let's keep it Fun, and Successful..
  • U-Bolt Size: 1/2" Diam x 3- 1/16" Inside Width x 4- 5/16" Inside Height (Length).
  • Attention: When measuring for Your needed Height (Length), add 1" for the nut and washer..
  • Threading: 1/2"-13 with a thread length of 2- 1/2"..
  • U-Bolts and hardware are made out of 304 Stainless Steel..
  • These U-Bolts will fit on 3" x 3" cross members, such as 3" x 3" box steel..
Check Stock

Mopar 77072479 Dodge Durango Cat Back Exhaust

  • Genuine OEM Parts and Accessories offered by Molar (the Original Equipment Parts Supplier for Chrysler, Dodge, Jeep, Ram and Fiat vehicles).
  • Molar bolt-on, free flow cat-back exhaust systems feature T304 stainless steel construction (aircraft-quality) with mandrel-bent tubing, stainless band (Torch) clamps and polished tips.
  • They're rigorously designed and tested to provide horsepower and torque gains with improved fuel economy.
  • Give your vehicle a deeper exhaust tone without causing unwanted drone.
  • Vehicle must be equipped with 5. 7L Hemi Engine.
Check Stock

2PCS Exhaust Clamps 3 Inch Butt Joint Exhaust Pipe Muffler Clamp Band Stainless Steel Connection for Cars

  • Size: We offer you 2pcs exhaust clamps, which you can measure better before you buy. These fixtures feature a unitary construction that minimizes part count and maximizes material efficiency and weight..
  • Material: The band clamp is a wide band of metal, usually stainless steel, wrapped around the exhaust pipe joint. Our products are preformed rings and are now more commonly used in high-end aftermarket exhaust systems that use slip fit because they are relatively inexpensive and can be reused without damaging the pipe..
  • Flexible Disassembly and Repair: The butt strap clamp is a simple and effective way to connect exhaust system components such as pipes, mufflers and catalytic converters. Offering unique sealing and high clamping loads, it does not distort your exhaust components and provides flexible removal and repair..
  • Save Time and Effort: Distribute the clamping force evenly over the entire 360° range to prevent leakage and control material deformation. It is easy to install or disassemble with one bolt, saving time and effort. T-304 strip stainless steel and carbon steel galvanized hardware..
  • Satisfied Customer Service - Both product quality and payment, will always be guaranteed. We are responsible sellers, always providing high quality products a....
Check Stock

2X 2.0' Inch Stainless Steel Butt Joint Exhaust Band Clamp Sleeve for Exhaust Pipes, Mufflers and Catalytic Converters

  • HIGH QUALITY : The band is made of non-magnetic stainless steel for long durability and reliability, zinc-plated M10 flange bolt and nut, steel gasket, aluminum alloy I-block..
  • ADVANTAGE : It is very easy to solve the problem of replacing a section of the exhaust exhaust tubing without loosening multiple sections of exhaust tubing to install the flared connection, and it will make the connection very firm and very tight..
  • FUNCTION : Great solution for connecting 2 pipes of the same diameter! 360-degree clamping of the exhaust tubing to prevent exhaust leakage and noise.
  • INSTALL EASILY : You only need to link two tubing of the same size, then tie the strap clamp to it, and finally tighten the two screws..
  • WHAT YOU WILL GET : Two 2in Exhaust Bands, 12-month warranty, whatever the problem about this item you have, please contact us..
Check Stock