1 3/16\ Expansion Reamer, Carbide Tipped, Straight Shank, Partial Flute Carbide 56026P, USA Made
When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
1 7/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56080P, USA Made
When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
2" flute length, Partial Flute Length Carbide.
Morse taper shank #4, For Reaming Abrasive Material.
This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..
1 5/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56078P, USA Made
When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
4Pcs Drill Bridge/Construction Reamer Bit Set 3/8 1/2 5/8 3/4 with 1/2 Shank HSS Taper Chucking Reamer Bit Tool for Steel Metal Wood Alloy Drilling Hole with Aluminum Box
What it does: Heavy-duty high-speed steel bridge reamers,expand or align existing holes through mild steel, alloys, aluminum, wood, plastic, fiberglass, or any material of similar hardness prior to rivet or bolt installation, Deburring and trimming of holes in structural materials.
Application: Especially for steel, metal, alloy aluminum, brass, plastic, iron, nickel, copper, cast iron and other structural materials.
Design: Tapered point design allows reamer bits to enter irregular overlapping holes, aligning bolt holes.
High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.
Available in uncoated (bright) and black oxide finish.
Round shanks allow use with a wide variety of toolholding systems.
Square shank allows hand (straight and spiral flute) reamers to be held in a tap wrench or vise, depending on whether the reamer of the part is rotated.
5/8 Drill Bridge/Construction Reamer with 1/2 Shank Chuck,HSS Taper Bridge Reamer Bit Tool for Steel Metal Wood Alloy to Align Existing Hole and Enlarge Hole
The heavy duty high-speed steel bridge reamer is also called construction reamers,it used for aligning an existing hole and enlarging undersized hole prior to bolt or rivet installation.Our reamer bit aligns and enlarges pre-drilled holes ready for bolting..
Makes reaming holes out extremely easier than using large drill bits,the reamed hole is smooth without tear-outs. But there must be a existing hole or a pilot hole that is smaller than 5/8" before using our 5/8" Bridge/Construction Reamer..
The tapered point design permits the reamer bit to enter into the overlapping holes of out-of-line,make the bolt holes line up.Enlarging the holes in the steering knuckles and pitman arm..
The 5/8" bridge reamer bit is not a drill bit,only aligning reamer to aligh holes which are pre-drilled.If you need to expand a hole to 5/8". At first there must be a 3/8" pre-drilled hole,then ream out to 5/8"..
Commonly used in bridge,construction,steel erection and automotive truck trailer industries,specially use in structural materials such as steel, metal, alloy aluminum,brass,plastic,iron,nickel,copper,cast iron etc.Three symmetrically placed flats on shank provide positive grip in portable electric and pneumatic tools..
