NEIKO 40510A Car Battery Tester | 100 AMP 6 and 12 Volt Automotive Load Checker | CCA Analyzer
[CONVENIENT]: Whether for the home, garage, or at the shop, the Neiko battery load tester is portable and DIY compatible for diagnosing and applying load to car, van, boat, truck, SUV, motorcycle, RV and other automotive 6 & 12 volt batteries..
[QUALITY]: Tester body features protection-encased analog voltage meter display, anti-sparking internal switchgear and external handle grip at top for portable carrying..
[DURABLE]: Copper clamp connectors feature red positive and black negative rubber grips to easily designate test clip placement on battery terminals..
[PERFECT FOR MECHANICS]: Load on test switch (hold load for maximum of 10 seconds) draws battery current to simulate starter motor draw for accurately and easy to read determining battery condition..
[ACCURACY]: Technical specifications: Fixed load current of 100 AMP, 100 AMP load test for 12V batteries up to 1000 Cold Crank Amps, 50 AMP load test for 6V batteries up to 1000 CCA. Voltage accuracy of ± 0.2V..
[Strong and lightweight design, waterproof and dustproof] The input cable length is 5 Feet, the output cable length is 10 Feet, the total cable length is about 15 feet.
and product weight is 6 pounds， the packing total weight is about 8 pounds.
[Proprietary Function]Please note! When the charging plug is in poor contact with the battery holder or the temperature is too high due to other reasons, the yellow indicator light will flash strongly and lock the low current. When the plug temperature exceeds the alarm value, it will change from a strong flashing yellow light to a strong flashing red light, and the output will be turned off. Therefore, please do not cut the charging plug cable or replace it with another type of charging plug..
[Charging indicator] The battery power : 0-90% --- Green light flashing slow.
Valefod DC 5V Relay Module 1-Channel Relay Switch with Optocoupler Isolation High/Low Level Trigger, Pack of 10
【Control Devices】The 1-channel relay module uses genuine high quality DC5V relay and SMD opto-isolator supporting high/low level trigger, widely apply to control various AC/DC appliances, and other devices with large current..
【Load Range】NO(Normally open) maximum load < AC 250V/10A, < DC 30V/10A. Trigger current of opto-isolator: 5mA..
【Fault-tolerant Design】The relay will not operate even if the control line is disconnected..
【Universal Interface】Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation..
【High Compatibility】The relay module can be controlled directly by 5V logic signals from microcontroller(8051, AVR, PIC, DSP, ARM, Raspberry Pi, MSP430, TTL logic etc).
AC Current Sensing Switch Adjustable Current 0.2~30A Flameproof ABS Self Powered Sensing Switch Users Manual (Normally Open)
✔ Automation Equipment Control -- Control various automation industrial equipment, flashlights, buzzers, relays, microcontrollers, or other electrical load devices. An ideal choice for automated industrial equipment and power monitoring.
✔ High Accuracy Stable Performance -- Compared with traditional device, thermal protectors and other devices, it has the advantages of high accuracy, stable performance and long service life. Installation Form: Guide Rail 35mmDIN.
✔ Convenient Monitoring Detecting Current -- The current sense switch is for safety, simple, and convenient monitoring or detection of current in the electrical equipment. Threading Hole Diameter: 8mm. Shell Material: Fireproof ABS.
✔ Used In Industries Current Monitoring -- Widely used in substation, frequency conversion speed control device, inverter device, electrolytic plating, electric locomotive, street lamp monitoring, coal mine and other automation industries that need current monitoring.
✔ Electromagnetic Mutual Inductance Of Current -- Using the principle of electromagnetic mutual inductance of current, the advanced output detection, monitoring and protection alarm products developed by the non-power supply technology are adopted.
KORAD KA3005D - Precision Variable Adjustable 30V, 5A DC Linear Power Supply Digital Regulated Lab Grade…
◆ HIGH PRECISION INSTRUMENT WITH MANY UNIQUE FEATURES - Very Easy setup with a rapid adjustment knob. There are buttons to switch to course or fine adjustment and a button to switch to voltage or current selection. The input voltage is switchable between 110/220 Volts for use in all countries. It has 4 Memory Recall buttons so you can save time setting up the supply to your required conditions..
◆ 4 DIGITS READINGS WITH BACK-LIT LED DISPLAY - With a 0.001V and 0.001A resolution, 4 digits provide more accurate and clearer visible readout for the voltage and current values with only 1 knob, extremely durable and easily visible even in low-light usage, meeting the needs of most people, ideal for business, small labs or the hobbyist at home..
◆ HIGH-QUALITY WITH ESSENTIAL SAFETY - Grounding wire, thermal protection, voltage and current overload and short-circuit protection ensure the safety. The built-in quiet variable fan reduces the operational noise and prolongs the life of product. There is a load on and off button so you can safely connect your load to the supply. There is also a lock button to prevent accidental changes..
◆ CONSTANT VOLTAGE & CURRENT OPERATION MODE - Easy to dial in the desired voltage with the encoded-controlled adjustment kn....
(Load/Speed Index 77H) (Recommended Rim 3.50) (Dia. 25.50) (Width 6.00) (Max Load @ PSI 908 LBS @ 41.
All Elite 4 rear tires utilize Dunlop’s MT Multi-Tread technology with a long-wearing compound in the center of the tire and a lateral-grip compound on each shoulder, providing increased mileage without sacrificing handling..
New tread pattern helps provide class-leading wet-pavement performance, even wear over the life of the tire, and less road noise..
Available in radial and bias-ply construction, the Elite 4 fits hundreds of touring, cruiser and standard bikes, including current and non-current machines..
High-mileage, even-wear characteristics, and great grip- the all-new Elite 4..
CR Magnetics CR5211-100 DC Hall Effect Current Transducer with Single Element, DC, 003e=2K Output Load, 24 VDC +/-10%, 0-100 ADC Input Range, +/-10 VDC Output Range
Output signal DC: 0-5V / 0-10V /4-20mA three forms are available. The outer casing is made of self-extinguishing material, safe and durable..
The measured current AC: 0-10A / 20A / 50A can be selected. Magnetic hysteresis less than 1%, can be used in strong magnetic field conditions..
Mutual inductance current monitoring, high current detection accuracy, stable performance, safe isolation of input and output. It is used for AC current monitoring, detection, current overload protection, and is also used as an electronic switch for automatic control systems..
Through-heart structure design, isolation withstand voltage up to 2000V AC. It is suitable for various applications requiring current and voltage conversion..
Installation and using are easy and convenient, there is no need to connect the dc series into the circuit during measurement. It has the characteristics of strong overload ability, high precision, high isolation, high security, low power consumption and strong anti-interference ability..
ORCISH Battery Quick Connect Disconnect Electrical Plug 2-4 Gauge 175 Amps for Recovery Winch or Trailer (White)
Wide applications: the battery quick connector provides simple and convenient method for connect disconnect power to a winch or other electrical device such as remote battery chargers, power inverters, solar setups, trailers, or for any other purpose requiring a high-current, quick-disconnect connector.
Package comes with 6 sets 6-10 gauge battery quick connector, including 6 connectors, 12 terminal pins, 6 caps, enough quantity to meet your different needs or replacement.
Quality material: the battery quick connector plug is made of sturdy PC fire-retardant material with fitted rubber boot covers to protect against dust, moisture, have long service time.
Easily installation: you can install these battery cable quick connector disconnect plug quickly, insert the wires into the terminal pins, and then solder or crimp them, connector ends are identical, so either ends are suitable for connection to the power or load side.
Stable working environment: there are 12 terminal pins made of red copper coated with silver have strong electrical conductivity and reduce the resistance to ensure stable voltage and current.
