Best Testing Terminal Blocks

24/20-Pin ATX DC Power Supply Diagnostic/Breakout Board Module

  • 24-pins Standard ATX Connector, support 20 / 20+4 / 24 pins wire header. With latching button switch to control ATX power supply output ON/OFF..
  • Total 16 LEDs, it is convenient for you to diagnose the functions of all pins except COM/GND, therefore, if the output of any one wire of your ATX power supply is faulty, it can be seen at a glance..
  • High quality screw terminal blocks. Each terminal position support current output maximum 10 Amp. Pitch 5.0mm/0.197 inch, Wire range 26AWG to 12AWG / 2.5mm square..
  • Packing list: 1x Diagnostic breakout board, 4x Screws, 4x Nylon spacers..
  • Special Note: The PS_ON LED lights up when the output is OFF and goes out when the output is ON, this is just the opposite of the indication status of other LEDs. Since many new ATX power supplies no longer provide output -5V, the NC/-V LED will not light up when connected to this type ATX power supply..
Check Stock

MESR-100 Capacitor Tester,Geevorks Circuit Tester Ohm Meter 0.001-100.0R with SMD Test Clip,Auto-Ranging Capacitor for Measuring Capacitance Resistance Circuit

  • This MESR-100 V2 auto-ranging capacitor ESR and low Ohm meter measuring range is 0.001-100.0R, support in circuit testing..
  • It is the series resistance inside the capacitor, and 100kHz is used to remove the impedance 1/(2*pi*F*C). When the impedance becomes smaller, the real series resistance value can be measured to determine whether the capacitor is bad/damaged or in good condition..
  • Our ESR meter only applies less than 15mV DC or peak to peak on a good capacitor, as a result we can use it as in circuit test..
  • During repairing TV, LCD, Audio board, etc. we can in circuit testing the capacitor is good or not.【Note:The Capacitance Meter is used for testing the internal resistance of the capacitor, not for testing capacitance value.】.
  • Dual terminal, for fast and easy inspect general capacitor or resistor, a printed ESR table for fast check.Equipped with a SMD alligator clip for more accurately testing..
Check Stock

YSTOOL Terminal Release Kit, Universal Wire Connector Removal Pin Extractor Release Tool 23 PCS Set for American Domestic and Imported Vehicles

  • Terminal release kit provides all the tools necessary for the damage-free releasing work of plug type connectors. Includes 23pcs release tools of various shapes and sizes to help remove terminals from electrical connectors and eliminates damage to wires or terminal blocks. Makes it safer and more efficient..
  • This kit fits for a wide range of models from home and abroad. Suitable for most American, European and Japanese cars and trucks which has electrical terminal and cables. Widely fits Ford, BMW, Mercedes, Opel, Porsche, Audi, Jaguar, etc. Ideal addition to your garage..
  • Tools come packed in a heavy-duty plastic blow-molded carrying case for easy transportation, simple storage, and quick organization.
  • Each handle of pin extractors is identified with numbers for quick reference to the well-illustrated application chart.
  • Constructed of alloy steel, these extractors are designed for maximum strength and longevity. Has rustproof surface and some adjustable pins. Rubber handle applies ergonomics, providing comfortable & non-slip grip, and insulating performance..
  • We supply 1 year warranty, please feel free to purchase. Any quality issue with the product, you are promised to exchange or refund the problematic parts for free. Please contact us to resolve any ....
Check Stock

[10 Pack] BESTTEN 15 Amp GFCI Receptacle Outlet, Tamper-Resistant (TR) GFI Outlet with LED Indicator, Ground Fault Circuit Interrupter, Wallplate Included, ETL Certified, White

  • ...red, the outlet will not have any power, making it more safe than conventional receptacles..
  • TEST FUNCTION. The receptacle will not reset normally if the GFCI circuit is not functioning properly. If GFCI has been wired properly, you can press the RESET button fully and it will supply the power to outlet and the load terminal.
  • Press the TEST button to test the GFCI and will stop the flow of electricity. This GFCI Outlet has LED Indicator lights to let you know the power, connection and protection status of the receptacle..
  • EASY INSTALLATION. Mounting screws are shipped captive in the device and wall plate for easier installation. It replaces an existing outlet only spend as short as 10 minutes. Wall plate and Complete installation instructions included..
Check Stock

Monoprice Professional Networking Tool Kit 107055

  • Punch Down Tool For 110 Type Terminal Blocks.
  • It Is A UTP/STP, Flat Cable Stripper Cutter.
  • Cable Tester : Tests RJ-45-EIA 568A/568B , 10 Base-T, Token Ring, RJ11/12 USOC And Coaxial BNC Cables.
Check Stock

Permatex 85120 Liquid Electrical Tape, 4 oz , Black

  • Weatherproof protectant for wiring and electrical connections.
  • Goes on as a liquid and dries to a flexible vinyl polymer.
  • Resists dirt, dust, chemicals, and moisture, ensuring that connections stay intact.
  • Brush top applicator allows coverage without gaps.
  • Suggested Applications: Ignition Wires, Underground Wiring, Outdoor Lighting Fixtures, Bilge Pumps, Terminal Blocks, Exposed Wires.
Check Stock

Fastronix 5/16' - 1/4' Stud Terminal Cover 2 Pack (Red)

  • Use with 5/16" or Smaller Studs to Fit over Nut.
  • Improve the Appearance of Your Power and Grounding Studs.
  • Use with Fastronix 406-251 Junction Blocks.
Check Stock

Blue Sea Systems Terminal Block Jumper for 30A Terminal Blocks, Pack of 5

  • Jumpers allow creation of common circuits on independent connectors.
  • Fits 30 Ampere terminal blocks (2500 Series).
Check Stock

MESR-100 Capacitor Tester, Geevorks ESR Meter in Circuit Capacitor Tester Up to 0.001-100.0R, Auto-Ranging Ohm Meter

  • This MESR-100 auto-ranging capacitor ESR and low Ohm meter measuring range from 0.001 to 100.0R, support in circuit testing..
  • Capacitance meter is a series resistor inside capacitor, using 100kHz to remove the impedance 1/(2*pi*F*C).The impedance become small, and we can then measure the true series resistor value..
  • Our ESR meter only applies less than 15mV DC or peak to peak on a good capacitor, as a r-esult we can use it as in circuit test..
  • Dual terminal, for fast and easy inspect internal resistance of the capacitor, a printed ESR table for fast check..
  • Note:The Capacitance Meter is used for testing the internal resistance of the capacitor, not for testing capacitance value.[Note: without SMD test clips].
Check Stock

Lisle 75500 Combustion Leak Detector

  • Checks for combustion leaks caused by bad head gaskets, cracked blocks, and cracked or warped heads.
  • Fluid changes from blue to yellow when exposed to combustion gases from the radiator.
  • With the engine running, the vehicle vacuum or the vacuum pump draws vapors through the indicating fluid for testing.
Check Stock