Joywayus Hex Nipple 1/2' Male x 1/2' Male Threaded Stainless Steel 304 Threaded Nipple Pipe Fittings for Brew Kit Home Piping (Pack of 5)
【Size】1/2" Male x 1/2" Male Thread. Tapered thread. Pipe fittings are components used for connecting, terminating, controlling flow, and changing the direction of pipe..
【High Quality Material &Threads】Made of quality stainless steel 304, durable and sturdy corrosion resistance, ductility at high temperatures, and low magnetic permeability. High quality and deep threads allow the fittings to bite better, tight threads, not easy to slip..
【Hex Nipple】The hex nipple fitting is a short length of pipe with threaded ends for connecting threaded pipes, and it has a hexagonal section in the middle for an increased bearing surface when adjusting the fitting with a wrench..
【Operating temperature range】Temperature rating: -65 to 250 degrees F.
【Widely Applications】Male threads for connecting to female threaded pipes, this premium pipe fitting can be used to connect various pipes, such as air pipe, fuel pipe, water pipe as well as air tools.
it can also be used with grease, fuels, LP and natural gas, refrigeration, instrumentation and hydraulic systems in low and medium pressure pipe line connections..
The 4 way LT PVC pipe fitting, also known as a side outlet tee or 4 way corner fitting is commonly used to build the sides of a box or cube out of PVC pipe. It is also useful to make the ridge on PVC greenhouses or small PVC buildings. Some dog agility customers use the 4 way LT at the base of jump pole stands..
All four outlets are non-threaded sockets.
2" Fittings fit on 2" Schedule 40 PVC or Furniture Grade PVC. Please check out our PVC Sizing Guide (Specification Sheet) to make sure that you order the correct size PVC Fittings. PVC is NOT measured by the outside diameter, and doing so will result in receiving fittings that are too big for your pipe..
Furniture Grade means this fitting has a non-marked, glossy finish..
Compression Sleeve Puller Tool Remove Nut & Ferrule Of Pipe 03943, Sleeve Remover For 1/2” Compression Fittings Only, Corroded & Frozen Supply Stops, Plumbing Tools Compression Ring Removal Tool
...s durable, corrosion resistant & wear resistant. Even such as the existing supply stops are severely corroded or frozen, you can turn the lever to extract the old compression sleeve from the pipe..
【Easy & Fast Remove】1.Remove the old compression fitting or the old angle stop. 2.Put the nut of pipe to the golden threaded mouth of the puller tool to tighten the screw 3.Make sure the ferrule puller is properly aligned with the pipe, and then you are able to remove the nut and ferrule with maybe 10 turns of the handle. 4.The puller tool will automatically pull compression nut and ferrule..
【Great Compression Sleeve Puller Tool】We love and take pride in our angle stop puller and we back this ferrule blaster up with lifetime service. Have the confidence that this compression ring removal tool will last, if there are any issues of this plumbing tools, just contact us and we will make it right..
Furniture Grade means this fitting has a non-marked, glossy finish..
DO NOT use these fittings for plumbing projects..
The 4 way LT PVC pipe fitting, also known as a side outlet tee or 4 way corner fitting is commonly used to build the sides of a box or cube out of PVC pipe. It is also useful to make the ridge on PVC greenhouses or small PVC buildings. Some dog agility customers use the 4 way LT at the base of jump pole stands..
1-1/2″ Fittings fit on 1-1/2″ Schedule 40 PVC or Furniture Grade PVC. Please check out our PVC Sizing Guide (Specification Sheet) to make sure that you order the correct size PVC Fittings. PVC is NOT measured by the outside diameter, and doing so will result in receiving fittings that are too big for your pipe..
1\ Pipe Fitting Tee DN25 Threaded Cast Black Malleable Iron for Steampunk Vintage Shelf Bracket DIY Plumbing Pipe Decor Furniture (10, 1\)
SIZE&QUANTITY: DN15 1/2-Inch pipe fittings compatible with standard 1/2-Inch pipe nipples. We send you 10 PCS pipe tees(size:1.37*1.12*1.79inch). It’s enough for you to DIY your furniture..
MALLEABLE CAST IRON - High quality malleable cast iron is perfectly anti-rust in oil and gas. Durable and no flexibility cast iron always used in many industry buildings. But malleable cast iron is unprocessed and needs to be cleaned and sealed to prevent rust before use...
WIDE APPLICATION - You can use these pipe fittings to install a durable iron frame f or your pipe shelving, wall lamp or other home décor..
EASY TO USE - These pipe fittings are threaded, just connect the threaded rods or pipes to the tees and elbows, you can easily to build any shape of frame and shelf for a DIY furniture as you like. Don’t need any screws..
100% MONEY-BACK GUARANTEE - We offer 90 days unconditional refund or replacement service if there are any quality issues. Contact us at any time and we will give you a satisfying answer. Just take a chance of our corner braces and we promise that you will not be disappointed..
SharkBite U3523LFA Stop Valve Connector Plumbing Fitting, Compression Push-to-Connect PEX, Copper, CPVC, 1/4 inch (3/8 inch OD) x 3/8 inch
INSTALLS IN SECONDS: 1/2 inch push-fit x 3/8 inch threaded compression angle shut off valve requires no special tools, no soldering, no crimping or glue. Just push to create a watertight seal.
PERFORMANCE: Rated to 200 PSI and 200 Degree F. Use in Potable water and Hydronic Heating applications.
VERSATILTY: SharkBite connects Copper, PEX, CPVC, and PE-RT Pipe in any combination.
QUALITY: Only SharkBite's quality and performance is field-proven with more than 550 million connections. SharkBite is the only push-to-connect brand than can ensure a clean, leak-free connection.
RESIDENTIAL and COMMERCIAL: All SharkBite fittings meet the same standards for commercial and residential plumbing applications.
PVC MATERIAL - PVC for corrosion resistance, high strength, and less weight than fittings made from metal, saving cost and accelerating the project....
THREAD & 150 WOG - Female threaded for connecting to male threaded pipe fittings. 150WOG working pressure, suitable for irrigation and water supply..
SAFETY - T handle for manual on/off control, easy operation.
Santoprene seats and stem packing reduce the risk of leakage..
ASTM - 1-1/2’’ ball valve, suitable for indoor and outdoor use like with cess-pipe, landscape and irrigation, pool, cold water, venting, waste....
DURABLE - Each valve individually tested for maximum safety blow-out proof stem, ageing resistant and long service life..
1/2\ Pipe Fitting Tee DN15 Threaded Cast Black Malleable Iron for Steampunk Vintage Shelf Bracket DIY Plumbing Pipe Decor Furniture (10, 1/2\)
SIZE&QUANTITY: DN15 1/2-Inch pipe fittings compatible with standard 1/2-Inch pipe nipples. We send you 10 PCS pipe tees(size:1.37*1.12*1.79inch). It’s enough for you to DIY your furniture..
MALLEABLE CAST IRON - High quality malleable cast iron is perfectly anti-rust in oil and gas. Durable and no flexibility cast iron always used in many industry buildings. But malleable cast iron is unprocessed and needs to be cleaned and sealed to prevent rust before use...
WIDE APPLICATION - You can use these pipe fittings to install a durable iron frame f or your pipe shelving, wall lamp or other home décor..
EASY TO USE - These pipe fittings are threaded, just connect the threaded rods or pipes to the tees and elbows, you can easily to build any shape of frame and shelf for a DIY furniture as you like. Don’t need any screws..
100% MONEY-BACK GUARANTEE - We offer 90 days unconditional refund or replacement service if there are any quality issues. Contact us at any time and we will give you a satisfying answer. Just take a chance of our corner braces and we promise that you will not be disappointed..
4LIFETIMELINES Fitting Assortment 1/4 Tube Nut Union Adapter 8 SKU
Contains 8 SKU, fast moving 1/4" fittings to keep on hand when working with automotive hydraulic braking systems.
Fitting Assortments are designed for specialty and general repair shops. Each assortment contains a specific collection of fast-moving brake line fittings that should be kept on hand when working with automotive hydraulic braking systems..
Assortments are packaged in shatter-resistant, see-through plastic trays. Locator labels on the inside lid make locating, selecting, and re-filling brake fittings quick and easy..
Compatible with steel, copper nickel, copper coated steel, PVF-coated, and stainless steel brake lines.
Lifetime warranty included on all products purchased from 4Lifetimelines.
