Best Uart Support

SEEU. AGAIN 4pcs 0.96 Inch I2C OLED Display Module IIC SSD1306 128x64 LCD White with 4 Pin Female to Female Du-pont Wire

  • I2C mode up to 400Khz, configurable slave address.
  • Two pin 3.3V UART mode, baud rates {9600, 19200, 38400, 57600, 115200}.
  • 4-pin SPI mode, supports all 4 standard SPI modes, up to 3Mhz clock.
  • Backlight brightness and contrast controlled by software commands.
  • Source code examples for custom applications, showing how to interface with the LCD from any I2C/UART/SPI hardware.
Check Stock

UNI-T UT210E Pro + UTG932, Digital Clamp Meter, Function Generator Arbitrary Waveform 30MHz 200MSa/s

  • Higher waveform capture rate Up to 200,000wfms/s waveform capture rate, greatly improving the capture pole The ability of low-probability events can more intuitively observe signal jitter and glitches, 256-level grayscale and color difference fluorescent display effect, waveform changes are visible..
  • Rich data measurement functions Support 34 kinds of automatic measurement parameter functions, Support Zoom, Math, statistics and advanced calculation functions..
  • Independent time base adjustable The time base of each channel is independently adjustable, and it has 4 windows display at the same time, which is convenient for users to observe four signals with large frequency differences.
  • Possess rich triggering and decoding functions, as well as waveform recording and playback functions Support bus decoding: I²C, SPI (only four channels), USB, CAN, optional: RS232/UART. Up to 100,000 frames waveform record,Record the waveform changes, replay the waveform conveniently, and analyze the fault.
  • UPO3254E 250MHz 4 2.5 GSa/s 70 Mpts 200000 wfms/s UPO3154E 150MHz 4 2.5 GSa/s 70 Mpts 200000 wfms/s.
Check Stock

RIGOL DS1074Z-S Plus Digital Oscilloscope, 4 Channels, 70MHz, 1Gsa/s, 24Mpts, 30000wfms/s, Built-in 25MHz Function/Arbitrary Waveform Generator, Free Trigger and Decoding

  • 70 MHz, upgradable to MSO, 16 digital channels. Built-in 2-channel 25 MHz function generator, real-time sample rate 1 GSa/s and up to 24 Mpts memory can support zoom in a selected part of the captured waveforms to get more details and scroll within the measurement points. Various standard triggers and bus decodes Triggers: Windows, Nte Edge, Delay, Timeout, Runt, RS232 / UART, I²C and SPI Decoding: RS232/UART, I2C, SPI.
  • Up to 30,000 wfms/s waveform detection rate, allowing users to capture instant signals and abnormal signals faster. Up to 60,000 recorded waveforms can be easily recorded, displayed and analyzed. This also helps to improve the ability to capture waveforms and accelerate a circuit debug course..
  • 7-inch WVGA TFT LCD (800 x 480), multi-level grading intensity display, extensive signal properties with a very large number of readings can also be fully displayed. The waveform retention is adjustable. A modern and advanced waveform mathematics system can easily solve complicated signal calculations with pre-defined formulas..
  • Automatic measurement of 37 waveform parameters (with statistics): such as rise and fall time, amplitude, pulse width, working cycle and much more simultaneously and shows statistics for each parameter (max, min and avera....
Check Stock

Matek F405 VTOL STM32F405RGT6 Flight Controller Built-in OSD MicroSD Card Slot 2~6S ArduPilot INAV For FPV RC Drones Multirotor Fixed Wing Airplane

  • USB/Beep Extender with Type-C(USB2.0)，Built in inverter on UART2-RX for SBUS input Switchable Dual Camera Input.
  • INAV: MATEKF405TE_SD (INAV 5.0 or newer).
  • Support continuous load of up to 100A on ESC pad near the current sensor resistor.
  • Support continuous load of up to 30A & peak of 50A on each ESC pad of Quadcopter.
  • Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, Buzzer, GPS module, AirSpeed.
Check Stock

5V ESP8266 Dual Channel WiFi Relay Module IOT Smart Home Phone APP Remote Switch with 100M Transmission Distance

  • ON-BOARD ESP-01 WIFI MODULE: The relay board is equipped with on-board ESP-01 WiFi module and high performance microprocessor STM8S103..
  • UART DEBUG INTERFACE: The relay has reserved UART debug interface and STM8 SWIM program download interface..
  • SMART CONFIG TECHNOLOGY: The module uses smart config technology to complete the account and password configuration on the APP ESP-01 WiFi module on the mobile phone, and configure the username and password memory functions..
  • ON-BOARD 5V RELAY: This relay module adopts On-board 5V,10A250V AC 10A30V DC relay, which can continuously pull 100,000 times with diode discharge protection and short response time..
  • WORKING STATUS INDICATOR: The module has board mode selection and real-time working status indicator..
Check Stock

Ingcool Raspberry Pi Pico Senser Kit, Raspberry Pi Pico Microcontroller Board with Flexible Digital Interfaces,Based on RP2040 Microcontroller Chip,Include Humidity,Color,Liquid Sensors

  • RP2040 microcontroller chip designed by Raspberry Pi in the United Kingdom.Dual-core Arm Cortex M0+ processor, the flexible clock running up to 133 MHz.
  • 264KB of SRAM, and 2MB of onboard Flash memory.Castellated module allows soldering direct to carrier boards.USB 1.1 with device and host support.
  • Low-power sleep and dormant modes.Drag-and-drop programming using mass storage over USB.
  • 26 × multi-function GPIO pins.2 × SPI, 2 × I2C, 2 × UART, 3 × 12-bit ADC, 16 × controllable PWM channels.8 × Programmable I/O (PIO) state machines for custom peripheral support.
  • Accurate clock and timer on-chip.Temperature sensor.Accelerated floating-point libraries on-chip.
Check Stock

SainSmart LA104 Handheld 4-Channel Logic Analyzer w/ 2.8\ Color TFT Screen SPI I2C UART Programmable 100Msa/s Max Sampling Rate

  • Compact Design: Equipped with a rich 2.8" 320x240 TFT display and side thumbwheels allow for easy operation and navigation..
  • Wide Application: Analyze UART, I2C, SPI, and many other standard protocols accepted. This unit is specially designed for UART, SPI, I2C, and other communication debugging..
  • Portable: Its small form factor conveniently fits inside any pocket so it's always ready on the go!.
  • Easy Saving: The built-in 8 MB flash storage makes saving images and transferring data easier than ever!.
  • Simple to Use: Product instructions are provided, but if you have any more concerns, SainSmart provides more details in their wiki page and customer assistance with any questions that may arise!.
Check Stock

BIGTREETECH Direct Octopus V1.1 Silent 32 Bit Control Board 3D + TFT35 E3 V3.0 Two Mode Display Screen 3D Printer Parts for Creality Ender 3/5 CR10

  • 【Main Control Chip】Uses a 32-bit ARM Cortex-M4 series STM32F446ZET6 main control chip with a core frequency of 180MHz..
  • 【Strong DIY Support】This motherboard supports up to 8 stepper drivers with 9 stepper driver outputs in total.
  • 【Realize Online Printing】Interfaces with a Raspberry Pi using emulated serial over USB or direct UART to any of the serial ports on the board, to....
  • 【Motherboard Expansion Function】Support BLTouch, locked-rotor detection, shutdown after printing, resume printing after power failure, CAN bus, U....
  • 【Increase Protection Function】Uses high-performance MOSFETs to increase heating efficiency while also reducing heat generation on the motherboard.....
Check Stock

USB to RS485 Level Serial UART Converter Cable FTDI Chipset 6 Way Wire End Stripped Cable USB-RS485-WE-1800-BT

  • USB RS485 UART Serial Converter Adapter Cable Compatible USB-RS485-WE.
  • 6ft/1.8m in length , with new original FTDI chipset import from UK.
  • Signal Output: GND-Black, Data- -Yellow, Data+ Orange, 5V power-red, Termintor1-brown, Terminator 2-green.
  • FT232RL & SP485leen , TX, RX LED Shows design on PCBA.
  • System Support: All windows system, Win7/8/10/xp/mac/linux/android, environment PVC jacket & pure copper wires, Central Package.
Check Stock

Creality 3D Printer Part Limit Switch with Separate Package CNC for RAMPS 1.4 RepRap 3D Printer CR-10 10S,S4,S5,Ender 3/Ender 3 Pro/Ender 3 V2/Ender 5 (Pack of 3)

  • 1.Upgrade the firmware by SD card. It is easy and convenient to operate.This display board has higher compatibility. Users can select two work modes,they are UART serial port screen mode and 12864 screen mode..
  • 2.Serial port screen mode supports two printing modes: SD card and U disk..
  • 3.Reserve WIFI port, and WIFI function is realized by external WIFI module.
  • 4.Reserve the extension port of filament breaking detection (FIL-DET).
  • Reserve the extension port of automatic shutdown after printing (PS-ON).
  • 5.2 sets of UART serial port extension ports are reserved for DIY use..
Check Stock