UHF Fiberglass Mobile Radio Antenna,70CM 400-470mhz GMRS Base Antenna 17inch So239 Connector for Ham Radio Device Repeater Mobile Transceiver with Antenna Mount Bracket
[Simple construction,Easy Tuning and Assembly]The surface is made of aluminum alloy,Antioxidant,make the antenna bright and clean,sturdy and durable,good environmental adaptability.Lightweight,High strength,Waterproof,Corrosion resistant..
The body of the Yagi Antenna makes it highly resilient to outdoor use. Strong wind resistance,Rated wind velocity 60 m/s.Securely attached to the mounting surface with the U-Bracket..
High gain benefit,great front to back ratio.
Yagi Antenna greatly increase the signal strength of your radio,strong anti-jamming,provides stable signal,hit your repeater easily,get long distance communication..
Yagi Antenna Widely used in various directional divice:For Baofeng Motorola Yaesu Kenwood amateur 2 Way Radio.
onelinkmore BNC to UHF Antenna Adapter BNC Female to UHF Male PL259 Connector Coaxial BNC UHF Radio Adapter for Antennas LAN Device Radios Mobile Kenwood Radio Amateur Scanner SWL Operator Pack of 2
Application for BNC Antennas, Wireless LAN Devices , Coaxial cable, Wi-Fi Radios External Antenna,Can be used for connecting a BNC male cable to SO-239 jack female such as a radio or an antenna.
This UHF to BNC adapter provide a simple way to put the SWR meter with SO239 Ports in-line in your car without changing your setup.
Compatible with Vehicle CB Radio Amaterur Radio Ham Radio Marine VHF Radio Antenna Analyzer.
Package Content : 2 x BNC to UHF Connector RF Adapter.
onelinkmore SMA Female to SO239 Female RF Two Way Radio Coax Adapter UHF Jack SO-239 Antenna Cable Connector for CB Radio Walkie Talkie SDR UV-5R Series Handheld Radio Pack of 2
UHF Female to SMA Female Adapter Converter.
Well Constructed and Connection Pins Are Gold-plated for Secure Connections,The connector housing and pin in center are made of pure brass,the shell is gold-plates and nickel-plates ,to ensure a lower VSWR for higher transmission efficiency..
Used widely at UHF,VHF Frequency Connect and Radio Station Antenna Convertion.
Not only allow you to attach antenna to the CB radio, and great used with DMR HT with an external antenna, but also works well to adapt from rooftop scanner antenna to RTL-SDR dongle.
Package Content : 2 x SMA Female to UHF Female Adapter.
Tram Browning 1191 Amateur Dual Band Glass Mount Antenna UHF 440-450 MHz and VHF 144-148 MHz PL-259 for Icom HYT Vertex Mobiles two way radio antenna
TWAYRDIO RH660S telescopic ham radio antenna, high quality high gain with low SWR, help you get longer communication range. Can retractable and extendable, more convenient for you bring outside.
Dual Band Rafio Antenna/ Frequency: VHF/UHF(70cm/2m), work on 136-174mhz/400-470mhz, performs best on 144/430MHZ.
With the retractable design with 6 sections, this portable UHF VHF Antenna can be shortened or extended, when the antenna is retracted it is 11'’ and when the antenna full extended, it is up to 42’’. Changeable length provide more clear communication for you..
Radio anetenna connector type: SMA-Male . With gain 3.0/5.5dBi signal with up to 10W power. V.S.W.R less1.5.
Compatible with Two -way handheld radio: YAESU/Vertex Standard VX-210 VX-210A VX-300 VX-400 VX-410 VX-414 VX-417 WouXun KG-UV6D KG-UV6DPRO KG-UV8D ICOM IC-F50V IC-F50.
AURSINC SHARI PiHat - Portable SA818 Ham Allstar Radio Interface Compatible with Raspberry Pi 2/3/4 | Raspberry Pi Hosted Allstar Node | UHF Frequency Range 1W 420-450MHz/70cm | Amateur Radio Operator
[What Is It] Small, portable with self contained radio and antenna, SHARI(SA818 Ham Allstar Radio Interface) is designed for construction and uses in the amateur radio service, works with a Pi2/Pi3 or Pi4, SHARI RF output power is 500 to 1000(default) milliwatts.
[Allstar Node] SHARI PiHatU implements a Raspberry Pi hosted Allstar node using a NiceRF SA818 embedded UHF (420-450 MHz|70cm) radio module.
In order to create an Allstar node, SHARI plugs into two USB jacks on a Raspberry Pi2/Pi3 or Pi4 for power, the Allstar interface and radio programming (a short M/F USB extender cable can be used if desired) ;Note: only work with allstar node or any analog node.
[Power Supply] SA818 Ham Allstar Radio Interface is a power supply intended for the version of the Raspberry Pi. These supplies typically provide 5.1 to 5.2 VDC to the Pi. Current requirements vary with version. Numerous problems with Allstar Nodes have been traced to inadequate power supplies..
[Feature 1] Front panel LEDs indicate the status of SHARI-POWER (green), USB Audio CONNECTION STATUS (blinking green), COS (green) and PTT (red).
SHARI PiHat uses 5 volts from the Pi, and the best place to measure it is from pin 8 (+5) to pin 9 (GND) of the SA818 module.
RedYutou cb Antenna Cable UHF(M) Dual Male (3.3 feet/100cm) RG58 Coax for HAM & CB Radio,Antenna Analyzer,Dummy Load,SWR Meter Short Wave Radio - HF, VHF, UHF
RG58 Coax CABLE UHF Male PL259 to UHF Male PL-259 Digital Coax Cable (1 pack).
Connector: UHF Male (M head) Brass material Nickel-plated on the outside (gold-plated inner conductor)>1300 Times Mating Life Time..
Suitable for Antennas. CB Radio Handheld and Amateur Radio Equipment.Antenna Analyzer. Radio Scanner. Ham Radio Transceiver. SWR METER. Short Wave Radio - HF, VHF, UHF 。Coaxial, switcher, combiner, power splitter.
AEDIKO 2pcs Police Radio Scanner Antenna Car Truck Adhesive Mount Ham Radio Mobile Scanner Antenna VHF UHF 20-1300MHz BNC Male Antenna
BNC Male Antenna: Frequency Range: 20MHz – 1300MHz.
Adhesive Mounting: Police Radio Scanner Antenna Come with Car Window Glass Adhesive Mounting.
with BNC Male Connector widely used for Public Radio Scanner, Ham Radio, Two Way Radio, Walkie Talkie, Mobile Radio.
Application: Compatible With Indoor Radio Tuner AV Audio Vedio Home Theater Receiver Stereo Receiver with Bluetooth Power System Speaker Selector Music System.
Powerwerx DB-750X Dual Band VHF/UHF 750 Channel Commercial Mobile Radio
...des all of the necessary mounting hardware to easily wire into any vehicle. You can use the UV-50X2 as a base station at home or in the office with the optional RPS-30M power supply (not included)..
Recommended Accessories: Pair UV-50X2 with the Nagoya UT-72 Magnetic Mount Antenna for easy installation. The PC04 FTDI Cable is recommended for easy computer programming.
The UV-50X2 operates as multiple radios in one, with either 144 MHz or 430 MHz as the "Main" TX/RX band, while simultaneously watching up to 3 other frequencies or channels.
and, if you like, you can configure your UV-50X2 for simultaneous VHF-VHF or UHF-UHF operation, too!.
Kit Includes: BTECH UV-50X2, RJ45 to K1 Audio Adaptor, Speaker Mic, DC Cable, Radio & Mic Brackets, Mounting Hardware, and User Guide.
HYS TCJ-N1 3/8 to 3/4 Hole Mount with NMO Bracket L Shape Fender Mount 13 /About 4m RG-58 Coax Cable NMO to PL259 for All VHF/UHF/CB Radio NMO Antenna
The mount is a "trunk lid" mount with 13'/about 4m RG-58U cable. This requires a small (typically 3/8" to 3/4" ) hole be drilled through the surface....
L-Bracket Hole Stainless Steel 3/4" NMO Hole Mount, L Bracket for HYS TCJ-N1 Coax NMO Mount Cable Mobile Antennas Car Truck Hood install. Stainless....
Prefect for mobile FM transceiver NMO antennas. NMO to PL259 working for so239/uhf female Motorola Yaesu/Vertex Kenwood HYT Icom radio, the clip need....
This is a high quality, low profile base mount that does the job very well. 13 feet NMO cable connected easily with the antenna and there is plenty of....