Best Usb To Serial Ttl Converter

6PCS 3D Printer TMC2208 V1.2 Stepper Motor Driver, TMC2208 Stepstick Stepper Motor Driver Module with Heat Sink Screwdriver for 3D Printer Controller Boards Reprap Ramps1.4 MKS Gen Ender-3 Pro

  • TMC2208 is an ultra-quiet two-phase stepper motor drive chip, continuous drive current 1.4A, peak current 2A, voltage range 4.75V-36V, 256 subdivision..
  • The flexible microPlyer interpolation unit provides up to 256 subdivisions, allowing perfect sinusoidal control even in systems with limited pulse frequencies.
  • these are also designed because stealthChop2 ultra-quiet technology is widely used in 3D printing..
  • Compatible with existing 3D printer electronics, eliminating the expensive costs of redesign. It can replace the original TMC2100 A4988 DRV8825 LV8729, lower heat, especially for 3D printing market..
  • With this adapter you can test your SilentStepStick or flash the TMC2208 SilentStepStick with an USB-to-serial converter..
  • The adapter comes with stackable headers, so you can use it direct on your 3D printer board. The tester is pre-configured for standalone operation on an USB to serial adapter (VIO-VM jumper closed)..
Check Stock

DIYmalls BN-180 GPS Module TTL Dual Glonass GPS + GPS Passive Antenna for Arduino Raspberry Pi Pixhawk Aircraft CC3D Betaflight Flight Control

  • BN180 GPS Module can show your speed. When you use it for Raspberry Pi, there is no driver needed. Here is connection with RPi, red to 3.3v, black to....
  • When you power up bn 180 GPS module the first time in a new location, it always takes longer to find satillites. This is referred to as “cold....
  • Data Level : TTL or RS-232,Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable.
  • BN 180 gps doesn't have flash and compass. If you need it, please buy bn-880 gps module via "Visit the DIYmalls Store".
  • If you have any problem, please contact seller as follow: click "DIYmalls"(you can find "Sold by DIYmalls" under Buy Now button), in the new page,....
Check Stock

4PCS TMC2208 3D Printer Stepper Motor Driver TMC2208 V1.2 Stepstick Stepper Driver Module Carrier with Heat Sink Screwdriver for 3D Printer Controller Boards Ramps 1.4 MKS Gen Mega i3 Ender-3 Pro

  • TMC2208 is an ultra-quiet two-phase stepper motor drive chip, continuous drive current 1.4A, peak current 2A, voltage range 4.75V-36V, 256 subdivision..
  • The flexible microPlyer interpolation unit provides up to 256 subdivisions, allowing perfect sinusoidal control even in systems with limited pulse frequencies.
  • these are also designed because stealthChop2 ultra-quiet technology is widely used in 3D printing..
  • Compatible with existing 3D printer electronics, eliminating the expensive costs of redesign. It can replace the original TMC2100 A4988 DRV8825 LV8729, lower heat, especially for 3D printing market..
  • With this adapter you can test your SilentStepStick or flash the TMC2208 SilentStepStick with an USB-to-serial converter..
  • The adapter comes with stackable headers, so you can use it direct on your 3D printer board. The tester is pre-configured for standalone operation on an USB to serial adapter (VIO-VM jumper closed)..
Check Stock

Geekstory BN-220 Dual GPS Glonass Module Navigation TTL Level 9600bps + GPS Passive Antenna for Arduino Raspberry Pi Pixhawk F3 CC3D Betaflight F4 Flight Control

  • BN-220 gps module has flash to save configuration, so you do not need to reset data next time when you use it. But it has no compass. If you need gps with flash and compass, please buy bn-880 from Geekstory..
  • When you use it for Raspberry Pi, there is no driver needed but you need to install software.
  • The TX LED flash means gps module output normally.The PPS LED flash means gps module locate your place..
  • Data Level : TTL or RS-232,Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable.
  • BN 220 gps module documentation link cannot be displayed. If you need technical documentation, please click “Ask a question” to em-ail us.
Check Stock

GCAN-207 RS232/485 to CAN Converter,Realize bidirectional Communication Between RS232 or RS485 Bus and CAN Bus

  • Standard serial port level, RS232 model or RS485 model can switch by software.
  • Conversion direction can be set to: CAN?? Serial, CAN?Serial, CAN?Serial.
  • Serial Bus baud rate range from 600bps to 115200bps.
  • CAN-Bus supports CAN2.0A and CAN2.0B frame format, conform to ISO/DIS 11898 standards.
  • CAN-Bus baud rates range from 5Kbps to 1Mbps.
  • CAN-Bus interface with electrical isolation.
  • CAN-Bus isolation converter insulation voltage: DC 1500V.
  • Working temperature range from -40 to 85 °C.
Check Stock

AVITAL 3305L 3305L Responder 2-Way Security System with 4-Button LCD Remote

  • dedicated A-to-D converter samples your vehicle’s voltage hundreds of times each second, eliminating the need for a tachometer wire connection.
  • Product 1: D2D serial data port Quickly connects your Avital system to other interface devices via D2D cable.
  • Product 1: XCR onboard relays Extreme capacity remote start relays are built-in to Avital remote start systems..
  • Product 2: D2D serial data port Quickly connects your Avital system to other interface devices via D2D cable.
  • Product 2: XCR onboard relays Extreme capacity remote start relays are built-in to Avital remote start systems..
Check Stock

USB to RS485 Level Serial UART Converter Cable FTDI Chipset 6 Way Wire End Stripped Cable USB-RS485-WE-1800-BT

  • USB RS485 UART Serial Converter Adapter Cable Compatible USB-RS485-WE.
  • 6ft/1.8m in length , with new original FTDI chipset import from UK.
  • Signal Output: GND-Black, Data- -Yellow, Data+ Orange, 5V power-red, Termintor1-brown, Terminator 2-green.
  • FT232RL & SP485leen , TX, RX LED Shows design on PCBA.
  • System Support: All windows system, Win7/8/10/xp/mac/linux/android, environment PVC jacket & pure copper wires, Central Package.
Check Stock

Active DVI to VGA Adapter , UVOOI Male DVI-D (24+1) to VGA Female Monitor Converter Video for Docking Station, Computer, Monitor, HDTV, Projector

  • Add one serial RS-232 port with com retention to any laptop or computer with a USB port.
  • Simple installation and operation with COM port retention provides robust serial connectivity for legacy devices with minimal hassle.
  • Easy plug and play installation with USB Powered device - no power outlet required.
  • Extensive list of compatible operating systems makes this device perfect for almost any RS232 application.
  • USB to Straight-Through RS232 Serial Adapter.
  • COM Port assignments maintained across reboot.
  • Powered by an available USB port - no external power adapter required.
Check Stock

Cable Matters USB to Serial Adapter Cable (USB to RS232, USB to DB9) 3 Feet

  • USB to RS232 adapter cable connects from the USB-A port of a computer to a device with a female DB9 port.
  • Bus-powered Serial to USB adapter connects to devices for configuration or programming.
  • Male to male serial to USB cable provides a convenient solution for communicating with equipment that require a DB9 connector.
  • Use a DB9 mini gender changer (sold separately) if the connector of the RS232 to USB adapter will not mate with the equipment port.
  • Simple installation of the USB Serial adapter using the drivers available for download from Cable Matters.
  • Connect a null modem adapter (sold separately) to directly connect two computers with serial cables.
  • Windows & Mac compatible USB to Serial cable for Windows 2000/XP/Vista/7/8/10 and MacOS 10.6 and above.
  • The 9 pin to USB adapter may require additional proprietary software some equipment models.
  • RS-232 compatible db9 to USB adapter is required for many types of equipment including a CNC Machine, GPS, telescope, Set-top box, Cisco network switch, sewing Machine and more.
Check Stock

C2G USB Adapter USB to DB25 Adapter Grey 6 Feet (1.82 Meters) Cables to Go 22429,Gray

  • Cable must be used with existing DB25 serial device cable..
  • Quickly convert your DB25 serial device to USB.
  • Perfect for connecting a serial device to a laptop or PC's USB port.
  • Compatible with USB 1.1, USB 2.0 and USB 3.0 ports.
  • This product creates a virtual serial port. It is not intended to connect a parallel printer/device to a USB port. The parallel port device is part number 16899.
Check Stock