300A 16㎡ Copper Clad Aluminum Cable Dinse 10-25 Connector Plug Welding Leads Assembly Set 9.8ft Welding Electrode Holder and 6.5ft Stick Plier Ground Clamp for ARC Stick MMA Mini Welding Rod Welder
✨ This kind of Welding Electrode Holder is made of Copper Clad Aluminum clamp head and special insulation heat-resistant material. High temperature resistance, non-conductive, suitable for long-term use.
✨ The Welding Ground Clamp is also suitable for stick,tig,mig or cut welding.Features wide grip jaws to ensure a firm connection.Grounds work can be welded to a good electrical ground earth.
✨ 9.8ft long Welding Electrode Holder with cable and 6.5ft long Welding Ground Clamp with cable. 16㎡cable,Dinse 10-25 connector.*-*Please check connector size in the picture and compare with your welder´s Connector/Receptacle to make sure it fits*-*.
✨ This Welding Leads Assembly Set has a strong current(300A).It is not easy to scald with copper forging.Also,the welding electrode rod in the Electrode Holder is not easy to fall off for the high strength Multi-angle occlusion.You will receive a ready to use fully assembled lead, no tools required.
✨ This set of welding accessories have a common advantage: Copper guide, Copper Clad Aluminum wire, stable and durable, thick handle, high-quality upper and lower jaws, not easy to oxidize with heat, strong bite force.
Siglent Technologies SDG1062X Series Dual-Channel Function/Arbitrary Waveform generators
【Specifications】Voltage Supply: 9-12V DC Input.
Input Distortion: less than 1% (at 1KHz).
【welding steps】The welding installation considerations, follow these steps: First,the components are welding the front board, from low to high principles, namely the first low welding components, such as, capacitor, resistor, diode, etc.Then welding IC socket, terminal blocks, finally power socket, adjustable potentiometer..
【Debugging steps】After completion of welding on IC, XR2206, you need to pay attention to the direction of IC, or insert the might damage the chip! Check IC for errors, if any, please correct in time..
【Power】 Insert the power supply, power supply for 5.5 x 2.1 port, inside and outside is negative polarity.
Fitting for 9-12 v power supply voltage, and the waveform may not be stable for more than 12V..
【Please note】these are DIY kits, you need to follow the welding steps in our description and complete the final installation..
ABN L5-50R Connector – 50 Amp Twist Lock Inlet Locking Power Cord Connector Locking Power Inlet Plug 50A 125/250V
CONNECT YOUR CABLE: Use your generator, transfer switch, welding equipment, trailer, RV camper power inlet with this ABN Inlet Locking Connector.
KEEP OUT PESTS: Replace your power cord with this twist lock connector so the cord can be removed and stored without leaving an opening that mice or....
SECURELY HOLD CABLE: This connector comes with strain reliefs that mount inside the base of the connector to hold the cable (clamp for the cord).
PERFECT SIZE: Approximate measurement across the face is 2 inches (5.1cm).
Across the back where the cord enters adds 0.25 inch (2.25 inches / 5.7cm....
Remove housing by loosening face screws and slide over cable (If a weather-resistant boot is used, slide this over....
Spot Welder with Soldering Iron, 11000mAh Soldering Iron Kit Electronics, Adjustable Temperature Welding Tool, Portable Spot Welding Equipment for DIY 18650 Battery, Soldering Iron Stand
✔Multifunctional 2-in-1: Professional welding machine + soldering iron two-in-one function, easy to carry..
✔Multi-purpose - The spot welder can be used to spot weld cylindrical lithium batteries, nickel-metal hydride batteries and 18650/26650/32650 batteries such as cadmium-nickel batteries, and our mobile phone batteries can also be spot welded..
✔Adjustable Gears - The spot welding machine has 6 gears that can be adjusted. Different gears are used for different materials. The spot welding materials can be nickel, iron, stainless steel, aluminum, etc. 0.1-0.2 mm in thickness material..
✔Large Capacity - The spot welder has a large capacity of 11000 mAh, built-in rechargeable 2 electric power lithium batteries, discharge current 003e650A, environmentally friendly. Type-C 2A input, it can be fully charged in about 3 hours. We can also use it to charge our other devices..
✔Protection Measures - The portable spot welder with soldering iron has perfect overcharge and over temperature protection functions. Its unique overheating protection device automatically cuts off the power when overheating occurs, and it will automatically shut down without any operation for 8 minutes, allowing you to use it more safely..
Plasma Cutter TIG Welder Pulse Stick Welder - CT418 3 in 1 Combo Welding Machine 180A Pulse TIG/Arc Welding 40A Plasma Cutting 110/220V Dual Voltage Digital Display Portable Welder Machine
❆ Advantage: We have updated our CT418 machine. Under the condition that the basic functions remain unchanged, our machine has increased the PULSE function to make the welding effect even better. And the machine adopts a brand-new digital panel, which is easier to set up and operate. It is still an automatic dual voltage dual frequency (110/220V, 50/60HZ)..
❆ 10-40Amp Plasma Cutter: 40amp plasma cutter current output @220V. Compact plasma cutter has a handle for portability and uses non-hazardous compressed air to cut stainless steel, alloy steel, mild steel, copper, and aluminum.
❆ PULSE TIG Welder: 10-180A Pulse TIG Welder Electric Current Output @ 220V. Quality TIG welding on stainless steel, nickel alloys, copper, brass and bronze etc. The newly added PULSE function makes the welding shape more beautiful and improvers tungsten life..
❆ What You Get: Our worry-free 12-month warranty, and friendly customer service. The CT-418 machine comes with a PT-31 cutting torch, TIG-17FV torch for tig welding. You also get stick holder, earth clamp, power cable, air hose, and torch co....
Jacazooy Welding Electrode Holder 4.9ft Stick Copper Plier Ground Clamp MMA Mini Welding Rod Copper Clamp Tool Accessories With Cable
✔️The goods are mixed in black and white and shipped randomly. Please don’t take the order if you mindThe Welding Electrode Holder is made of all copper clamp head and special insulation heat-resistant material. High temperature resistance, non-conductive, suitable for long-term use..
✔️The Welding Ground Clamp is suitable for a welding arc.Features wide grip jaws to ensure a firm connection.Grounds work to be welded to a good electrical ground earth..
✔️ This welding accessories is made of copper clamp head, strong current.It is not easy to scald with pure copper forging.Also,the welding electrode rod in the Electrode Holder is not easy to fall off for the high strength Multi-angle occlusion..
✔️The welding accessories have a common advantage: Copper guide, pure copper wire, stable and durable, thick handle, high-quality upper and lower jaws, not easy to oxidize with heat, strong bite force..
✔️ The Welding Electrode Holder with cable is 6.5ft long and the Welding Ground Clamp with cable is 4.9ft long. Please allow the manual measurement data to deviate slightly. (0.1-0.2ft error).
TIG-225HF integrates advanced MOSFET inverter technology, allowing excellent arc stability and the most beautiful welds. Whether the material is stainless steel, alloy steel, low carbon steel, copper, iron, pig iron, cast iron, etc., the welding effect is absolutely ideal.
the machine can be swiftly operated and can efficiently finish any tasks from home repairs or professional use. The new lightweight model design gives the machine an elegant structure and makes the machine very easy to carry..
TIG-225HF is a professional Argon arc welding machine with outstanding performance and a robust and elegant structure. This is an industrial level machine – high-frequency and high-voltage arcs are easy to start and ensure 100% perfection. The current of 10-225 amperes is very suitable for welding all types of thicknesses regarding work-pieces. The outstanding 80% duty cycle can also ensure long-time welding..
TIG-225HF is an intelligent power supply system built with a sleek and modern design. The automatic selection function can automatically detect the input voltage and will adjust to the suitable conditions on its own. Additionally, you can easily manually adjust it in the range of 95V to 260V for specific requests. This machine is designed for demanding ....
