UNIROI Raspberry Pi RAB Holder Breadboard Kit with 830 Points solderless Circuit Board Raspberry Pi Holder for Arduino, Mega 2560 & Raspberry Pi 4B, 3B+, 3B, 2B and 1B+, A+ (52 Items)
This 14 in 1 RAB Holder kit is designed by for the Raspberry Pi and Arduino hobbyists, the holder is large enough for a Raspberry Pi 4B/ 3B/ 2B/ 1B+/ Zero/ Zero W, Arduino 328P Control Board or Mega 2560, and a 400 hole or 830 hole Circuit Board breadboard.
Including RPi GPIO Breakout Expansion Board and Ribbon Cable, which are special for Raspberry Pi 3 Model B, 2 Model B, 1 Model B+ and zero/ zero W..
This 830-tie/point breadboard includes an IC area of 630 points, plus two 100-point distribution strips, providing 4 power rails..
Comes with male-to-male 65pcs jumper wires, red, green, and yellow LEDs (three for each color), ten 1k resistors, a screwdriver, and some screws..
Gift: GPIO 40 pin Table Card for wiring Pi and BCM codes for all RPI motherboard..
HiFiBerry HighPi Raspberry Pi Case - Raspberry Pi4
High quality ABS plastic case, designed and made in Canada, Large internal volume for HATs, break-out boards, or heat sinks, Vents on three sides double as fly-through cable ports, Self-adhesive rubber feet included, set of 4, Matte finish hides fingerprints.
External dimensions: 97 x 66 x 41mm, Internal volume for breakout boards: 90 x 60 x 28.8mm.
New Version ATX Power Supply Breakout Board and Acrylic Case Kit with ADJ Adjustable Voltage Knob, Supports 3.3V, 5V, 12V and 1.8V-10.8V (ADJ) Output Voltage, 3A Maximum Output, Reset Protection.
1.ATX power supply breakout board, with ADJ adjustable voltage knob, supports 3.3V, 5V, 12V and 1.8V-10.8V (ADJ) output voltage..
2.The voltage output terminals of the ATX power expansion board correspond to each screw terminal..
3. At the same time, the panel is also equipped with an acrylic case kit for easy to use..
4.Compatible with 3.3V: STM32 MCU, network communication equipment, such as Wi-Fi Bluetooth and other devices, generally for microcontrollers, and some low-power modules, etc. 5V: Raspberry Pi, Banana Pi, Tinker Board, Nano Pi, USB interface, etc..
5.Compatible with 9V: Arduino, motor drive, display driver module, etc. 12V: motor drive, LED light, vehicle equipment with power requirements less than 24w, etc..
Includes the BBC micro:bit v2 With 8 accessories to get you started with all kinds of Microbit Projects.
The BBC micro:bit v2 (launched November 2020) is the same size and shape as the original micro:bit with many upgrades.
Great Introduction to the world of coding.
Includes USB cable to code and power and a Battery Holder to power on the go (Batteries NOT included) and 6 Alligator clips, Breadboard, a selection of Jumper wires, a Breakout board to be used with the breadboard and a Panel to hold the battery holder and breadboard and keep your projects neat.
All Parts Covered for 1 year under the Vilros Warranty.
Zrong 3D Printer Parts DRV 8825 DRV8825 Stepper Motor Driver Module 4 PCB Board Replace A4988
The DRV8825 stepper motor driver is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver..
The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver carriers, so it can be used as a....
The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It....
UPGRADED -- This Breakout LED Tail Light are a definite upgrade from the stock incandescent bulb version. More light functions, Brighter visibility, Stylish appearance..
LIGHT -- Bright, fast-acting LED lamps glow red when the ignition is on, and intensify when brakes are activated. Command the attention of following vehicles..
INSTALLATION -- Direct Replacement for your original one, no modification as required..
PACKAGE -- 1x LED Chopped Fender Edge Tail Light for Harley Softail Breakout.
StewMac Sun Fuzz DIY Electric Guitar Pedal Kit, With Bare Enclosure, Inspired By Analogman Sun Face (12252)
32 Page Step-by-step Instructions Written For The First Time Builder.
Road-worthy Rugged Metal Enclosure With All Holes Pre-drilled.
Other Great Features! 3PDT Breakout Board For Low Noise, Internal Trim Pots For Tone Shaping, Input, Output, And Power Jacks Rear Mounted For Easy Cable Routing, and it's True Bypass Just Like the Original Sun Face.
